- 您現在的位置：買賣IC網 > PDF目錄384025 > TP28F010-120 (INTEL CORP) 28F010 1024K (128K X 8) CMOS FLASH MEMORY PDF資料下載
參數資料
| 型號： | TP28F010-120 |
| 廠商： | INTEL CORP |
| 元件分類： | DRAM |
| 英文描述： | 28F010 1024K (128K X 8) CMOS FLASH MEMORY |
| 中文描述： | 128K X 8 FLASH 12V PROM, 120 ns, PDIP32 |
| 封裝： | 0.620 X 1.640 INCH, PLASTIC, DIP-32 |
| 文件頁數： | 11/33頁 |
| 文件大?。?/td> | 895K |
| 代理商： | TP28F010-120 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
E
28F010
11
Table 3. Command Definitions
First Bus Cycle
Second Bus Cycle
Command
Bus
Cycles
Req’d
Operation
(1)
Address
(2)
Data
(3)
Operation
(1)
Address
(2)
Data
(3)
Read Memory
1
Write
X
00H
Read Intelligent
Identifier Codes
(4)
3
Write
IA
90H
Read
IA
ID
Set-Up
Erase/Erase
(5)
2
Write
X
20H
Write
X
20H
Erase Verify
(5)
2
Write
EA
A0H
Read
X
EVD
Set-Up Program/
Program
(6)
2
Write
X
40H
Write
PA
PD
Program Verify
(6)
2
Write
X
C0H
Read
X
PVD
Reset
(7)
2
Write
X
FFH
Write
X
FFH
NOTES:
1.
2.
Bus operations are defined in Table 2.
IA = Identifier address: 00H for manufacturer code, 01H for device code.
EA = Erase Address: Address of memory location to be read during erase verify.
PA = Program Address: Address of memory location to be programmed.
Addresses are latched on the falling edge of the WE# pulse.
ID = Identifier Data: Data read from location IA during device identification (Mfr = 89H, Device = B4H).
EVD = Erase Verify Data: Data read from location EA during erase verify.
PD = Program Data: Data to be programmed at location PA. Data is latched on the rising edge of WE#.
PVD = Program Verify Data: Data read from location PA during program verify. PA is latched on the Program command.
Following the Read Intelligent ID command, two read operations access manufacturer and device codes.
Figure 5 illustrates the 28F010 Quick-Erase Algorithmflowchart.
Figure 4 illustrates the 28F010 Quick-Pulse Programming Algorithmflowchart.
The second bus cycle must be followed by the desired command register write.
3.
4.
5.
6.
7.
2.2.2.1
Read Command
While V
PP
is high, for erasure and programming,
memory contents can be accessed via the Read
command. The read operation is initiated by writing
00H into the command register. Microprocessor
read cycles retrieve array data. The device remains
enabled for reads until the command register
contents are altered.
The default contents of the register upon V
PP
power-up is 00H. This default value ensures that no
spurious alteration of memory contents occurs
during the V
PP
power transition. Where the V
PP
supply is hardwired to the 28F010, the device
powers-up and remains enabled for reads until the
command register contents are changed. Refer to
the AC Characteristics
—Read-Only Operations
and
waveforms for specific timing parameters.
2.2.2.2
Intelligent Identifier Command
Flash memories are intended for use in applications
where the local CPU alters memory contents. As
such, manufacturer and device codes must be
accessible while the device resides in the target
system. PROM programmers typically access
signature codes by raising A
9
to a high voltage.
However, multiplexing high voltage onto address
lines is not a desired system design practice.
The 28F010 contains an intelligent identifier
operation
to
supplement
programming methodology. The operation is
initiated by writing 90H into the command register.
Following the command Write, a read cycle from
address 0000H retrieves the manufacturer code of
89H. A read cycle from address 0001H returns the
device code of B4H. To terminate the operation, it
traditional
PROM-
相關PDF資料 |
PDF描述 |
|---|---|
| TP28F010-150 | 28F010 1024K (128K X 8) CMOS FLASH MEMORY |
| TP28F512-120 | 512K(64Kx8)CMOS FLASH MEMORY |
| TP3067BDW | MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER |
| TP13067BDW | MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER |
| TP3067BN | MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TP28F010-150 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:28F010 1024K (128K X 8) CMOS FLASH MEMORY |
| TP28F010-90 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:28F010 1024K (128K X 8) CMOS FLASH MEMORY |
| TP28F512-120 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:512K(64Kx8)CMOS FLASH MEMORY |
| TP29 | 制造商:B&K Precision Corporation 功能描述: |
| TP-29 | 功能描述:測試探頭 THERMOCOUPLE PROBE RoHS:否 制造商:Teledyne LeCroy 設備類型:Passive Probes 帶寬:500 MHz 尖端類型: 長度:1.3 mm 顏色:Black 電壓額定值: 電流額定值: |
發布緊急采購，3分鐘左右您將得到回復。