- 您現在的位置：買賣IC網 > PDF目錄383997 > TIBPAL16L8-7MJ (Texas Instruments, Inc.) HIGH-PERFORMANCE IMPACT-X E PAL CIRCUITS PDF資料下載
參數資料
| 型號： | TIBPAL16L8-7MJ |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | HIGH-PERFORMANCE IMPACT-X E PAL CIRCUITS |
| 中文描述： | 高性能影響組E PAL制式電路 |
| 文件頁數： | 16/30頁 |
| 文件大小： | 295K |
| 代理商： | TIBPAL16L8-7MJ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
TIBPAL16L8-5C, TIBPAL16R4-5C, TIBPAL16R6-5C, TIBPAL16R8-5C
TIBPAL16L8-7M TIBPAL16R4-7M TIBPAL16R6-7M TIBPAL16R8-7M
HIGH-PERFORMANCE
IMPACT-X
PAL
CIRCUITS
SRPS011D – D3359, OCTOBER 1989 – REVISED SEPTEMBER 1992
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
16
programming information
Texas Instruments programmable logic devices can be programmed using widely available software and
inexpensive device programmers.
Complete programming specifications, algorithms, and the latest information on hardware, software, and
firmware are available upon request. Information on programmers capable of programming Texas Instruments
programmable logic is also available, upon request, from the nearest TI field sales office, local authorized TI
distributor, or by calling Texas Instruments at (214) 997-5666.
asynchronous preload procedure for registered outputs (see Figure 1 and Note 3)
The output registers can be preloaded to any desired state during device testing. This permits any state to be
tested without having to step through the entire state-machine sequence. Each register is preloaded individually
by following the steps given below.
Step 1.
Step 2.
Step 3.
Step 4.
With V
CC
at 5 volts and Pin 1 at V
IL
, raise Pin 11 to V
IHH
.
Apply either V
IL
or V
IH
to the output corresponding to the register to be preloaded.
Lower Pin 11 to 5 V.
Remove output voltage, then lower Pin 11 to V
IL
. Preload can be verified by observing the
voltage level at the output pin.
tsu
+ t
h
td
td
VIHH
VIL
VOH
VOL
Registered Output
Pin 11
VIH
VIL
Output
Input
5 V
Figure 1. Asynchronous Preload Waveforms
Not applicable for TIBPAL16L8-5C and TIBPAL16L8-7M.
NOTE 3: td = tsu = th = 100 ns to 1000 ns
VIHH = 10.25 V to 10.75 V
相關PDF資料 |
PDF描述 |
|---|---|
| TIBPAL16R6-5CJ | HIGH-PERFORMANCE IMPACT-X E PAL CIRCUITS |
| TIBPAL16R6-7M | HIGH-PERFORMANCE IMPACT-X E PAL CIRCUITS |
| TIBPAL16R6-7MFK | HIGH-PERFORMANCE IMPACT-X E PAL CIRCUITS |
| TIBPAL16R6-7MJ | HIGH-PERFORMANCE IMPACT-X E PAL CIRCUITS |
| TIL189-2 | OPTOCOUPLERS/OPTOISOLATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TIBPAL16L8AMFK | 制造商:Texas Instruments 功能描述: |
| TIBPAL16LH-25CN | 制造商:Texas Instruments 功能描述: |
| TIBPAL16R4-10C | 制造商:TI 制造商全稱:Texas Instruments 功能描述:HIGH-PERFORMANCE IMPACT-X E PAL CIRCUITS |
| TIBPAL16R410CFN | 制造商:TI 功能描述:* |
| TIBPAL16R4-10CFN | 功能描述:SPLD - 簡單可編程邏輯器件 High-Performance Impact-X PAL Circuit RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24 |
發布緊急采購，3分鐘左右您將得到回復。