- 您現在的位置：買賣IC網 > PDF目錄98148 > STMPE2401TBR (STMICROELECTRONICS) 24 I/O, PIA-GENERAL PURPOSE, PBGA36 PDF資料下載
參數資料
| 型號： | STMPE2401TBR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 24 I/O, PIA-GENERAL PURPOSE, PBGA36 |
| 封裝： | LEAD FREE, TFBGA-36 |
| 文件頁數： | 6/55頁 |
| 文件大?。?/td> | 959K |
| 代理商： | STMPE2401TBR |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
I2C Interface
STMPE2401
14/55
6
I2C Interface
The features that are supported by the I2C interface are as below:
●
I2C Slave device
●
SDAT and SCLK operates from 1.8V to 3.3V
●
Compliant to Philip I2C specification version 2.1
●
Supports Standard (up to 100kbps) and Fast (up to 400kbps) modes.
●
7-bit device addressing mode
●
General Call
●
Start/Restart/Stop
●
Address up to 4 STMPE2401 devices via I2C
The address is selected by the state of two pins. The state of the pins will be read upon
reset and then the pins can be configured for normal operation. The pins will have a pull-up
or down to set the address. The I2C interface module allows the connected host system to
access the registers in the STMPE2401.
6.1
Start condition
A Start condition is identified by a falling edge of SDATA while SCLK is stable at high state.
A Start condition must precede any data/command transfer. The device continuously
monitors for a Start condition and will not respond to any transaction unless one is
encountered.
6.2
Stop condition
A Stop condition is identified by a rising edge of SDATA while SCLK is stable at high state.
A Stop condition terminates communication between the slave device and bus master. A
read command that is followed by NoAck can be followed by a Stop condition to force the
slave device into idle mode. When the slave device is in idle mode, it is ready to receive the
next I2C transaction. A Stop condition at the end of a write command stops the write
operation to registers.
6.3
Acknowledge bit (ACK)
The acknowledge bit is used to indicate a successful byte transfer. The bus transmitter
releases the SDATA after sending eight bits of data. During the ninth bit, the receiver pulls
the SDATA low to acknowledge the receipt of the eight bits of data. The receiver may leave
the SDATA in high state if it would to not acknowledge the receipt of the data.
相關PDF資料 |
PDF描述 |
|---|---|
| STMPE801MTR | 8 I/O, PIA-GENERAL PURPOSE, PDSO16 |
| STMPS2262MTR | 4 I/O, PIA-GENERAL PURPOSE, PDSO8 |
| STN8810B2S12HPI | 32-BIT, 264 MHz, RISC PROCESSOR, PBGA26 |
| STN8810BES12HPBE | 32-BIT, 264 MHz, RISC PROCESSOR, PBGA26 |
| STP1012PGA-110 | 32-BIT, 110 MHz, RISC PROCESSOR, CPGA321 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STMPE2403 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:24-bit Enhanced port expander with Keypad and PWM controller Xpander logic |
| STMPE2403TBR | 功能描述:接口 - 專用 24-bit Enhanced RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| STMPE24M31QTR | 功能描述:電容觸摸傳感器 S-Touch 24 Cap Sens 15fF 512 Steps 30pF RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| STMPE321 | 制造商:STMicroelectronics 功能描述:3-channel touchkey controller |
| STMPE321QTR | 功能描述:觸摸屏轉換器和控制器 3-channel CAP Touch Key Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
發布緊急采購，3分鐘左右您將得到回復。