- 您現在的位置：買賣IC網 > PDF目錄383840 > ST7LITE15F1B6 CLIP FUSE 10A 5X20MM PC MOUNT PDF資料下載
參數資料
| 型號： | ST7LITE15F1B6 |
| 英文描述： | CLIP FUSE 10A 5X20MM PC MOUNT |
| 中文描述： | ST7LITE1 - 8單電壓閃存EEPROM的MEMORY.DATA位MCU。 ADC的。 4定時器。的SPI |
| 文件頁數： | 12/122頁 |
| 文件大?。?/td> | 1716K |
| 代理商： | ST7LITE15F1B6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁
ST7LITE0, ST7SUPERLITE
12/122
1
4 FLASH PROGRAM MEMORY
4.1 Introduction
The ST7 single voltage extended Flash (XFlash) is
a non-volatile memory that can be electrically
erased and programmed either on a byte-by-byte
basis or up to 32 bytes in parallel.
The XFlash devices can be programmed off-board
(plugged in a programming tool) or on-board using
In-Circuit Programming or In-Application Program-
ming.
The array matrix organisation allows each sector
to be erased and reprogrammed without affecting
other sectors.
4.2 Main Features
I
ICP (In-Circuit Programming)
I
IAP (In-Application Programming)
I
ICT (In-Circuit Testing) for downloading and
executing user application test patterns in RAM
I
Sector 0 size configurable by option byte
I
Read-out and write protection against piracy
4.3 PROGRAMMING MODES
The ST7 can be programmed in three different
ways:
– Insertion in a programming tool. In this mode,
FLASH sectors 0 and 1, option byte row and
data EEPROM can be programmed or
erased.
– In-Circuit Programming. In this mode, FLASH
sectors 0 and 1, option byte row and data
EEPROM can be programmed or erased with-
out removing the device from the application
board.
– In-Application Programming. In this mode,
sector 1 and data EEPROM can be pro-
grammed or erased without removing the de-
vice from the application board and while the
application is running.
4.3.1 In-Circuit Programming (ICP)
ICP uses a protocol called ICC (In-Circuit Commu-
nication) which allows an ST7 plugged on a print-
ed circuit board (PCB) to communicate with an ex-
ternal programming device connected via cable.
ICP is performed in three steps:
Switch the ST7 to ICC mode (In-Circuit Communi-
cations). This is done by driving a specific signal
sequence on the ICCCLK/DATA pins while the
RESET pin is pulled low. When the ST7 enters
ICC mode, it fetches a specific RESET vector
which points to the ST7 System Memory contain-
ing the ICC protocol routine. This routine enables
the ST7 to receive bytes from the ICC interface.
– Download ICP Driver code in RAM from the
ICCDATA pin
– Execute ICP Driver code in RAM to program
the FLASH memory
Depending on the ICP Driver code downloaded in
RAM, FLASH memory programming can be fully
customized (number of bytes to program, program
locations, or selection of the serial communication
interface for downloading).
4.3.2 In Application Programming (IAP)
This mode uses an IAP Driver program previously
programmed in Sector 0 by the user (in ICP
mode).
This mode is fully controlled by user software. This
allows it to be adapted to the user application, (us-
er-defined strategy for entering programming
mode, choice of communications protocol used to
fetch the data to be stored etc.)
IAP mode can be used to program any memory ar-
eas except Sector 0, which is write/erase protect-
ed to allow recovery in case errors occur during
the programming operation.
相關PDF資料 |
PDF描述 |
|---|---|
| ST7LITE15F1M6 | CLIP FUSE 15A VERT ATO PC MOUNT |
| ST7LITE19F1B6 | FUSE CLIP 3AG SLDR LUG TIN BRASS |
| ST7LITE19F1M6 | ST7LITE1 - 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY.DATA EEPROM. ADC. 4 TIMERS. SPI |
| ST890B | 1.2 CURRENT LIMITED HIGH SIDE WITH THERMAL SHUTDOWN |
| ST890C | 1.2 CURRENT LIMITED HIGH SIDE WITH THERMAL SHUTDOWN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST7LITE15F1M6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ST7LITE1 - 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY.DATA EEPROM. ADC. 4 TIMERS. SPI |
| ST7LITE19F1B6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ST7LITE1 - 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY.DATA EEPROM. ADC. 4 TIMERS. SPI |
| ST7LITE19F1M6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ST7LITE1 - 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY.DATA EEPROM. ADC. 4 TIMERS. SPI |
| ST7LITE1XB | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 5 TIMERS, SPI |
| ST7LITE1XB_08 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 5 TIMERS, SPI |
發布緊急采購，3分鐘左右您將得到回復。