- 您現在的位置：買賣IC網 > PDF目錄299943 > ST52501LF3 MAX 7000 CPLD 128 MC 100-PQFP PDF資料下載
參數資料
| 型號： | ST52501LF3 |
| 英文描述： | MAX 7000 CPLD 128 MC 100-PQFP |
| 中文描述： | 8位紅外驅動重癥監護病房。定時器/脈寬調制。 I2C總線。的SPI。脊髓損傷。低電壓 |
| 文件頁數： | 3/106頁 |
| 文件大?。?/td> | 1355K |
| 代理商： | ST52501LF3 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁
Figure 14.5 Clearing the WCOL bit (Write Collision Flag) Software Sequence
14.4.6 Overrun Condition.
An overrun condition occurs when the master
device has sent several data bytes and the slave
device hasn’t cleared the SPIF bit issued from the
previous data byte transmitted.
In this case, the receiver buffer contains the byte
sent after the SPIF bit was last cleared. A read to
the SPI_IN register returns this byte. All other
bytes are lost.
This condition is not detected by the SPI
peripheral.
14.4.7 Single Master and Multimaster Configu-
rations.
There are two types of SPI systems:
– Single Master System
– Multimaster System
Single Master System
A typical single master system may be configured,
using an ICU as the master and four ICUs as
slaves (see Figure 14.6).
The master device selects the individual slave
devices by using four pins of a parallel port to
control the four SS pins of the slave devices.
The SS pins are pulled high during reset since the
master device ports will be forced to be inputs at
that time, thus disabling the slave devices.
Note: In order to prevent a bus conflict on the
MISO line the master allows only one active slave
device during a transmission.
For more security, the slave device may respond to
the master with the data byte received. Then the
master will receive the previous byte back from the
slave device if all MISO and MOSI pins are
connected and the slave has not written its
SPI_OUT register.
Other transmission security methods can use ports
for handshake lines or data bytes with command
fields.
Multi-master System
A multi-master system may also be configured by
the user. Transfer of master control could be
implemented using a handshake method through
the I/O ports or by an exchange of code messages
through the serial peripheral interface system.
The multi-master system is principally handled by
the MSTR bit in the SPI_CR register and the
MODF bit in the SPI_STATUS_CR register.
Clearing sequence after SPIF = 1 (end of a data byte transfer)
1st Step
Read SPI_STATUS_CR
Read SPI_IN
Write SPI_IN
2nd Step
SPIF =0
WCOL=0
SPIF =0
WCOL=0 if no transfer has started
WCOL=1 if a transfer has started
Clearing sequence before SPIF = 1 (during a data byte transfer)
1st Step
2nd Step
WCOL=0
before the 2nd step
Read SPI_STATUS_CR
Read SPI_IN
Note: Writing in SPI_OUT regis-
ter instead of reading in SPI_IN
do not reset WCOL bit
Read SPI_STATUS_CR
OR
THEN
相關PDF資料 |
PDF描述 |
|---|---|
| ST52501LG1 | MAX 7000 CPLD 128 MC 160-PQFP |
| ST52501LG2 | MAX 7000 CPLD 128 MC 100-TQFP |
| ST52501LG3 | MAX 7000 CPLD 128 MC 100-TQFP |
| ST52501LK1 | MAX 7000 CPLD 160 MC 84-PLCC |
| ST52501LK2 | MAX 7000 CPLD 160 MC 100-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST52501LG1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT ICU WITH IR DRIVER. TIMER/PWM. I2C. SPI. SCI. LOW VOLTAGE |
| ST52501LG2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT ICU WITH IR DRIVER. TIMER/PWM. I2C. SPI. SCI. LOW VOLTAGE |
| ST52501LG3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT ICU WITH IR DRIVER. TIMER/PWM. I2C. SPI. SCI. LOW VOLTAGE |
| ST52501LK1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT ICU WITH IR DRIVER. TIMER/PWM. I2C. SPI. SCI. LOW VOLTAGE |
| ST52501LK2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT ICU WITH IR DRIVER. TIMER/PWM. I2C. SPI. SCI. LOW VOLTAGE |
發布緊急采購，3分鐘左右您將得到回復。