- 您現在的位置：買賣IC網 > PDF目錄10909 > SI3050-E1-GT (Silicon Laboratories Inc)IC VOICE DAA SYSTEM SIDE 24QFN PDF資料下載
參數資料
| 型號： | SI3050-E1-GT |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 60/128頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC VOICE DAA SYSTEM SIDE 24QFN |
| 標準包裝： | 74 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁當前第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
Si3050 + Si3011/18/19
Rev. 1.5
37
f. Set the OH bit to return to an off-hook state.
Immediately after returning to an off-hook state,
the off-hook counter must be allowed to expire.
This allows the line voltage to settle before
transmitting or receiving data. After 8 ms normal
data transmission and reception can begin. If a
non-compliant parallel device is present, then a
reply tone is not sent by the host tone generator
and the CO does not send the CID data. If all
devices on the line are Type II CID compliant,
then the host must mute its upstream data output
to avoid the propagation of its reply tone and the
subsequent CID data. When muting its upstream
data output, the host processor should return an
acknowledgement (ACK) tone to the CO
requesting transmission of CID data.
3. The CO then responds with CID data after receiving
the CID data, the host processor unmutes the
upstream data output and continues with normal
operation.
4. The muting of the upstream data path by the host
processor mutes the handset in a telephone
application so the user cannot hear the
acknowledgement tone and CID data being sent.
5. The CALD and the RCALD bits can be cleared to
re-enable the automatic calibrations when going
off-hook. The FOH[1:0] bits also can be programmed
to 01 to restore the default off-hook counter time.
Because of the nature of the low-power ADC, the data
presented on DTX can have up to a 10% dc offset. The
caller ID decoder must either use a high-pass or a
band-pass filter to accurately retrieve the caller ID data.
Figure 26. Implementing Type II Caller ID on the Si3050+Si3011/19
5.26. Overload Detection
The Si3050 can be programmed to detect an overload
condition that exceeds the normal operating power
range of the DAA circuit. To use the overload detection
feature, the following steps should be followed:
1. Set the OH bit (Register 5, bit 0) to go off-hook, and
wait 25 ms to allow line transients to settle.
2. Enable overload detection by then setting the OPE
bit (Register 17, bit 3).
If the DAA senses an overload situation it automatically
presents an 800
impedance to the line to reduce the
hookswitch current. At this time, the DAA also sets the
OPD bit (Register 19, bit 0) to indicate that an overload
condition exists. The line current detector within the
DAA has a threshold that is dependent on the ILIM bit
(Register 26). When ILIM = 0, the overload detection
threshold equals 160 mA. When ILIM = 1, the overload
detection threshold equals 60 mA. The OPE bit should
always be cleared before going off-hook.
Notes:
1. The off-hook counter and calibrations prevent transmission or reception of data for 402.75 ms (default) for the line
voltage to settle.
2.
The caller alert signal (CAS) tone transmits from the CO to signal an incoming call.
3.
The device is taken on-hook to read the line voltage in the LVS bits to detect parallel handsets. In this mode, no data is
transmitted on the DTX pin.
4.
When the device returns off-hook, the normal off-hook counter is reduced to 8 ms. If the CALD and RCALD bits are set,
then the automatic calibrations are not performed.
5.
After allowing the off-hook counter to expire (8 ms), normal transmission and reception can continue. If CID data
reception is required, send the appropriate signal to the CO at this time.
LINE
FOH[1] Bit
RCALD
Bit
CALD Bit
1
23
4
5
OH Bit
FOH[0] Bit
On-Hook
Off-H ook C ounter
and C alibration
(402.75 ms nominally)
Of f -Hook
CA S Tone
Rec eiv ed
On-Hook
Off-Hook Counter
(8 ms)
Of f -Hook
A ck
相關PDF資料 |
PDF描述 |
|---|---|
| VE-2NM-IX-F4 | CONVERTER MOD DC/DC 10V 75W |
| VE-2NM-IX-F3 | CONVERTER MOD DC/DC 10V 75W |
| VE-2NM-IX-F2 | CONVERTER MOD DC/DC 10V 75W |
| VE-2NM-IX-F1 | CONVERTER MOD DC/DC 10V 75W |
| VE-2NL-IX-F4 | CONVERTER MOD DC/DC 28V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI3050-E1-GTR | 制造商:Silicon Laboratories Inc 功能描述:SI3050 VOICE DAA SYSTEM-SIDE - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC VOICE DAA SYSTEM SIDE 24QFN 制造商:Silicon Laboratories Inc 功能描述:Si3050 Voice DAA System-Side |
| Si3050-E-FM | 功能描述:電信語音調制 IC Si3050 Voice DAA System-Side RoHS:否 制造商:Epson Electronics America 產品: 應用:Voice Guidance product 封裝 / 箱體:PQFP-52 電源電壓-最大:3.6 V, 5.5 V 最大工作溫度: 最小工作溫度: 封裝: |
| SI3050-E-FMR | 功能描述:電信線路管理 IC Si3050 Voice DAA System-Side RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3050-E-FS | 制造商:SILABS 制造商全稱:SILABS 功能描述:GLOBAL VOICE DAA |
| SI3050-E-FSR | 制造商:SILABS 制造商全稱:SILABS 功能描述:PCM highway data interface law A-law companding SPI control interface GCl interface |
發布緊急采購，3分鐘左右您將得到回復。