參數資料
型號： SC16C550BIBS,128
廠商： NXP Semiconductors
文件頁數： 18/48頁
文件大?。?/td> 0K
描述： IC UART SOT617-1
標準包裝： 6,000
特點： 可編程
通道數： 1，UART
FIFO's： 16 字節
電源電壓： 2.5V，3.3V，5V
帶自動流量控制功能： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 32-VFQFN 裸露焊盤
供應商設備封裝： 32-HVQFN（5x5）
包裝： 帶卷 (TR)
其它名稱： 935279497128
SC16C550BIBS-F
SC16C550BIBS-F-ND
SC16C550B_5
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 1 October 2008
25 of 48
NXP Semiconductors
SC16C550B
5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs
7.6 Modem Control Register (MCR)
This register controls the interface with the modem or a peripheral device.
Table 19.
Modem Control Register bits description
Bit
Symbol
Description
7
MCR[7]
reserved; set to ‘0’
6
MCR[6]
reserved; set to ‘0’
5
MCR[5]
Auto ow control enable.
4
MCR[4]
Loopback. Enable the local loopback mode (diagnostics). In this mode the
transmitter output (TX) and the receiver input (RX), CTS, DSR, DCD, and
RI are disconnected from the SC16C550B I/O pins. Internally the modem
data and control pins are connected into a loopback data conguration
(see Figure 11). In this mode, the receiver and transmitter interrupts
remain fully operational. The Modem Control Interrupts are also
operational, but the interrupts’ sources are switched to the lower four bits
of the Modem Control. Interrupts continue to be controlled by the IER
register.
logic 0 = disable loopback mode (normal default condition)
logic 1 = enable local loopback mode (diagnostics)
3
MCR[3]
OUT2. Used to control the modem DCD signal in the loopback mode.
logic 0 = OUT2 is at logic 1. In the loopback mode, sets OUT2 (DCD)
internally to a logic 1.
logic 1 = OUT2 is at logic 0. In the loopback mode, sets OUT2 (DCD)
internally to a logic 0.
2
MCR[2]
OUT1. This bit is used in the Loopback mode only. In the loopback mode,
this bit is used to write the state of the modem RI interface signal via
OUT1.
1
MCR[1]
RTS
logic 0 = force RTS output to a logic 1 (normal default condition)
logic 1 = force RTS output to a logic 0
0
MCR[0]
DTR
logic 0 = force DTR output to a logic 1 (normal default condition)
logic 1 = force DTR output to a logic 0
相關PDF資料
PDF描述
XR17C158CV-F IC UART PCI BUS 5V OCTAL 144LQFP
XR17D158CV-F IC UART PCI BUS OCTAL 144LQFP
ATMEGA168-15MZ MCU AVR 16K FLASH 15MHZ 32-QFN
XR17V258IVTR-F IC UART PCI BUS OCTAL 144LQFP
XR16L788IQTR-F IC UART FIFO 64B OCTAL 100QFP
相關代理商/技術參數
參數描述
SC16C550BIBS-F 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C550BIBS-S 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C550BIN40 制造商:NXP Semiconductors 功能描述:UART 16BYTE FIFO 16C550 DIP40
SC16C550BIN40,112 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C550IA44 制造商:NXP Semiconductors 功能描述:UART 16BYTE FIFO 16C550 PLCC44
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*