參數資料
型號: SAB-C161JC-32RF
廠商: INFINEON TECHNOLOGIES AG
英文描述: 16-Bit Single-Chip Microcontroller
中文描述: 16位單片機
文件頁數: 39/89頁
文件大?。?/td> 876K
代理商: SAB-C161JC-32RF
C161CS/JC/JI-32R
C161CS/JC/JI-L
Data Sheet
35
V3.0, 2001-01
Watchdog Timer
The Watchdog Timer represents one of the fail-safe mechanisms which have been
implemented to prevent the controller from malfunctioning for longer periods of time.
The Watchdog Timer is always enabled after a reset of the chip, and can only be
disabled in the time interval until the EINIT (end of initialization) instruction has been
executed. Thus, the chip’s start-up procedure is always monitored. The software has to
be designed to service the Watchdog Timer before it overflows. If, due to hardware or
software related failures, the software fails to do so, the Watchdog Timer overflows and
generates an internal hardware reset and pulls the RSTOUT pin low in order to allow
external hardware components to be reset.
The Watchdog Timer is a 16-bit timer, clocked with the system clock divided by 2/4/128/
256. The high byte of the Watchdog Timer register can be set to a prespecified reload
value (stored in WDTREL) in order to allow further variation of the monitored time
interval. Each time it is serviced by the application software, the high byte of the
Watchdog Timer is reloaded. Thus, time intervals between 20
μ
s and 671 ms can be
monitored (@ 25 MHz).
The default Watchdog Timer interval after reset is 5.24 ms (@ 25 MHz).
Oscillator Watchdog
The Oscillator Watchdog (OWD) monitors the clock signal generated by the on-chip
oscillator (either with a crystal or via external clock drive). For this operation the PLL
provides a clock signal which is used to supervise transitions on the oscillator clock. This
PLL clock is independent from the XTAL1 clock. When the expected oscillator clock
transitions are missing the OWD activates the PLL Unlock / OWD interrupt node and
supplies the CPU with the PLL clock signal. Under these circumstances the PLL will
oscillate with its basic frequency.
In direct drive mode the PLL base frequency is used directly (
f
CPU
= 2 … 5 MHz).
In prescaler mode the PLL base frequency is divided by 2 (
f
CPU
= 1 … 2.5 MHz).
Note: The CPU clock source is only switched back to the oscillator clock after a
hardware reset.
The oscillator watchdog can be disabled
by setting bit OWDDIS in register SYSCON.
In this case (OWDDIS = ‘1’) the PLL remains idle and provides no clock signal, while the
CPU clock signal is derived directly from the oscillator clock or via prescaler or SDD. Also
no interrupt request will be generated in case of a missing oscillator clock.
Note: At the end of an external reset (EA
= ‘0’) bit OWDDIS reflects the inverted level of
pin RD at that time. Thus the oscillator watchdog may also be disabled via
hardware by (externally) pulling the RD line low upon a reset, similar to the
standard reset configuration via PORT0. At the end of an internal reset (EA = ‘1’)
bit OWDDIS is cleared.
相關PDF資料
PDF描述
SAB-C161JC-LF 16-Bit Single-Chip Microcontroller
SAB-C161JI-32RF 16-Bit Single-Chip Microcontroller
SAB-C161JI-LF 16-Bit Single-Chip Microcontroller
SAK-C161CS-32RF 16-Bit Single-Chip Microcontroller
SAK-C161CS-LF 16-Bit Single-Chip Microcontroller
相關代理商/技術參數
參數描述
SAB-C161JC-LF 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:16-Bit Single-Chip Microcontroller
SAB-C161JC-LF CA 功能描述:16位微控制器 - MCU 16BIT ROM/ROMLESS RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
SAB-C161JC-LFCA 制造商:Infineon Technologies AG 功能描述:
SAB-C161JI-32RF 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:16-Bit Single-Chip Microcontroller
SAB-C161JI-LF 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:16-Bit Single-Chip Microcontroller