參數資料
型號： S1C63466F
元件分類： 微控制器/微處理器
英文描述： 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP144
封裝： PLASTIC, QFP8-144
文件頁數： 129/135頁
文件大?。?/td> 1053K
代理商： S1C63466F
S1C63466 TECHNICAL MANUAL
EPSON
85
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Serial Interface)
EISIF: Interrupt mask register (FFE3HD0)
Masking the interrupt of the serial interface can be selected with this register.
When "1" is written: Enabled
When "0" is written: Masked
Reading: Valid
With this register, it is possible to select whether the serial interface interrupt is to be masked or not.
At initial reset, this register is set to "0".
ISIF: Interrupt factor flag (FFF3HD0)
This flag indicates the occurrence of serial interface interrupt.
When "1" is read: Interrupt has occurred
When "0" is read: Interrupt has not occurred
When "1" is written: Flag is reset
When "0" is written: Invalid
From the status of this flag, the software can decide whether the serial interface interrupt.
This flag is set to "1" after an 8-bit data input/output even if the interrupt is masked.
This flag is reset to "0" by writing "1" to it.
After an interrupt occurs, the same interrupt will occur again if the interrupt enabled state (I flag = "1") is
set or the RETI instruction is executed unless the interrupt factor flag is reset. Therefore, be sure to reset
(write "1" to) the interrupt factor flag in the interrupt service routine before shifting to the interrupt
enabled state.
At initial reset, this flag is set to "0".
4.11.6 Programming notes
(1) Perform data writing/reading to the data registers SD0–SD7 only while the serial interface is not
running (i.e., the synchronous clock is neither being input or output).
(2) As a trigger condition, it is required that data writing or reading on data registers SD0–SD7 be
performed prior to writing "1" to SCTRG. (The internal circuit of the serial interface is initiated
through data writing/reading on data registers SD0–SD7.) In addition, be sure to enable the serial
interface with the ESIF register before setting the trigger.
Supply trigger only once every time the serial interface is placed in the RUN state. Refrain from
performing trigger input multiple times, as leads to malfunctioning. Moreover, when the synchronous
clock SCLK is external clock, start to input the external clock after the trigger.
(3) Setting of the input/output permutation (MSB first/LSB first) with the SDP register should be done
before setting data to SD0–SD7.
(4) Be aware that the maximum clock frequency for the serial interface is limited to 1 MHz when OSC3 is
used as the clock source of the programmable timer or in the slave mode.
(5) After an interrupt occurs, the same interrupt will occur again if the interrupt enabled state (I flag =
"1") is set or the RETI instruction is executed unless the interrupt factor flag is reset. Therefore, be sure
to reset (write "1" to) the interrupt factor flag in the interrupt service routine before shifting to the
interrupt enabled state.
相關PDF資料
PDF描述
S1C63567F0A0100 MICROCONTROLLER, PQFP144
S1C63653F 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, CQFP100
S1C6F567D0A0100 MICROCONTROLLER, UUC141
S1C6N3B0D0A0100 MICROCONTROLLER, UUC54
S1C6P366D0A0100 4-BIT, FLASH, 4.1 MHz, MICROCONTROLLER, UUC102
相關代理商/技術參數
參數描述
S1C63557D04Q000 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT
S1C63567 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63616 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63632 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63653 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*