- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C63455D 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC105 PDF資料下載
參數資料
| 型號： | S1C63455D |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC105 |
| 封裝： | DIE-105 |
| 文件頁數： | 94/119頁 |
| 文件大小： | 865K |
| 代理商： | S1C63455D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁當前第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁
68
EPSON
S1C63455 TECHNICAL MANUAL
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Serial Interface)
(2) Serial data input procedure and interrupt
The S1C63455 serial interface is capable of inputting serial data as parallel data, in units of 8 bits.
The serial data is input from the SIN (P10) terminal, synchronizes with the synchronous clock, and is
sequentially read in the 8-bit shift register. As in the above item (1), the synchronous clock used here is
as follows: in the master mode, internal clock which is output to the SCLK (P12) terminal while in the
slave mode, external clock which is input from the SCLK (P12) terminal.
Shift timing of serial data is as follows:
When negative polarity is selected for the synchronous clock (mask option):
The serial data is read into the built-in shift register at the falling edge of the SCLK signal when the
SCPS register is "1" and is read at the rising edge of the SCLK signal when the SCPS register is "0". The
shift register is sequentially shifted as the data is fetched.
When positive polarity is selected for the synchronous clock (mask option):
The serial data is read into the built-in shift register at the rising edge of the SCLK signal when the
SCPS register is "1" and is read at the falling edge of the SCLK signal when the SCPS register is "0".
The shift register is sequentially shifted as the data is fetched.
When the input of the 8-bit data from SD0 to SD7 is completed, the interrupt factor flag ISIF is set to
"1" and an interrupt is generated. Moreover, the interrupt can be masked by the interrupt mask
register EISIF. However, regardless of the interrupt mask register setting, the interrupt factor flag is
set to "1" after input of the 8-bit data.
The data input in the shift register can be read from data registers SD0–SD7 by software.
(3) Serial data input/output permutation
The S1C63455 allows the input/output permutation of serial data to be selected by the SDP register
(FF71HD3) as to either LSB first or MSB first. The block diagram showing input/output permutation
in case of LSB first and MSB first is provided in Figure 4.11.4.1. The SDP register should be set before
setting data to SD0–SD7.
SIN
Address [FF73H]
Address [FF72H]
Address [FF73H]
Address [FF72H]
Output
latch
Output
latch
SOUT
SD3 SD2 SD1 SD0
SD4 SD5 SD6 SD7
SD7 SD6 SD5 SD4
SD0 SD1 SD2 SD3
(LSB first)
(MSB first)
Fig. 4.11.4.1 Serial data input/output permutation
(4) SRDY signal
When the S1C63455 serial interface is used in the slave mode (external clock mode), SRDY signal is
used to indicate whether the internal serial interface is available to transmit or receive data for the
master side (external) serial device. SRDY signal is output from the SRDY (P13) terminal.
Output timing of SRDY signal is as follows:
When negative polarity is selected (mask option):
SRDY signal goes "0" (low) when the S1C63455 serial interface is available to transmit or receive data;
normally, it is at "1" (high).
SRDY signal changes from "1" to "0" immediately after "1" is written to SCTRG and returns from "0" to
"1" when "0" is input to the SCLK (P12) terminal (i.e., when the serial input/output begins transmit-
ting or receiving data). Moreover, when high-order data is read from or written to SD4–SD7, the SRDY
signal returns to "1".
When positive polarity is selected (mask option):
SRDY signal goes "1" (high) when the S1C63455 serial interface is available to transmit or receive data;
normally, it is at "0" (low).
SRDY signal changes from "0" to "1" immediately after "1" is written to SCTRG and returns from "1" to
"0" when "1" is input to the SCLK (P12) terminal (i.e., when the serial input/output begins transmit-
ting or receiving data). Moreover, when high-order data is read from or written to SD4–SD7, the SRDY
signal returns to "0".
相關PDF資料 |
PDF描述 |
|---|---|
| S1C63458F0A0100 | MICROCONTROLLER, PQFP144 |
| S1C63466D | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC140 |
| S1C63466F | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP144 |
| S1C63567F0A0100 | MICROCONTROLLER, PQFP144 |
| S1C63653F | 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, CQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63557D04Q000 | 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT |
| S1C63567 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63616 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63632 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63653 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。