- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C63455D 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC105 PDF資料下載
參數資料
| 型號： | S1C63455D |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC105 |
| 封裝： | DIE-105 |
| 文件頁數： | 29/119頁 |
| 文件大?。?/td> | 865K |
| 代理商： | S1C63455D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁
S1C63455 TECHNICAL MANUAL
EPSON
9
CHAPTER 2: POWER SUPPLY AND INITIAL RESET
2.2 Initial Reset
To initialize the S1C63455 circuits, initial reset must be executed. There are two ways of doing this.
(1) External initial reset by the RESET terminal
(2) External initial reset by simultaneous low input to terminals K00–K03 (mask option setting)
The circuits are initialized by either (1) or (2). When the power is turned on, be sure to initialize using the
reset function. It is not guaranteed that the circuits are initialized by only turning the power on.
Figure 2.2.1 shows the configuration of the initial reset circuit.
RESET
K00
K01
K02
K03
OSC2
OSC1
RQ
S
Internal
initial
reset
Divider
VDD
1 Hz
2 Hz
VDD
OSC1
oscillation
circuit
Noise
reject
circuit
Time
authorize
circuit
Mask option
Fig. 2.2.1 Configuration of initial reset circuit
2.2.1 Reset terminal (RESET)
Initial reset can be executed externally by setting the reset terminal to a low level (VSS). After that the
initial reset is released by setting the reset terminal to a high level (VDD) and the CPU starts operation.
The reset input signal is maintained by the RS latch and becomes the internal initial reset signal. The RS
latch is designed to be released by a 2 Hz signal (high) that is divided by the OSC1 clock. Therefore in
normal operation, a maximum of 250 msec (when fOSC1 = 32.768 kHz) is needed until the internal initial
reset is released after the reset terminal goes to high level. Be sure to maintain a reset input of 0.1 msec or
more.
However, when turning the power on, the reset terminal should be set at a low level as in the timing
shown in Figure 2.2.1.1.
VDD
RESET
2.0 msec or more
1.8 (2.0 or 2.2) V
0.5VDD
0.1VDD or less (low level)
Power on
Fig. 2.2.1.1 Initial reset at power on
The reset terminal should be set to 0.1VDD or less (low level) until the supply voltage becomes 1.8 V (2.0
V or 2.2 V) or more.
After that, a level of 0.5VDD or less should be maintained more than 2.0 msec.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C63458F0A0100 | MICROCONTROLLER, PQFP144 |
| S1C63466D | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC140 |
| S1C63466F | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP144 |
| S1C63567F0A0100 | MICROCONTROLLER, PQFP144 |
| S1C63653F | 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, CQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63557D04Q000 | 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT |
| S1C63567 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63616 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63632 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63653 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。