- 您現在的位置：買賣IC網 > PDF目錄385767 > RF3000 (RF Micro Devices, Inc.) SPREAD-SPECTRUM BASEBAND MODEM PDF資料下載
參數資料
| 型號： | RF3000 |
| 廠商： | RF Micro Devices, Inc. |
| 英文描述： | SPREAD-SPECTRUM BASEBAND MODEM |
| 中文描述： | 擴譜基帶調制解調器 |
| 文件頁數： | 16/28頁 |
| 文件大小： | 351K |
| 代理商： | RF3000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
11-336
RF3000
Rev A4 031216
High Gain Calibration Procedure
Calibration of an IEEE802.11b radio can be accomplished by sending a repetitive pattern to the radio at a known input
power, and adjusting the register settings until all packets are correctly received without errors or missing packets. A sim-
ple procedure is contained outlined as follows.
1. Write the six LSB's of register 21 to the value 011000 (24 decimal). This will decrease the total system gain.
2. Apply an 1Mbps IEEE802.11b signal to the input of the radio of a known input power (-75dBm).
3. Decrease the six LSB's of register 21 by one LSB until all packets are received correctly without dropping any pack-
ets.
4. Since the input power of the reference signal was set to -75dBm (to eliminate effects of thermal noise), calculate the
final register 21 setting by subtracting a known predetermined value from the value found in step 3 of the calibration
procedure.
Low Gain Calibration Procedure
Similar techniques can be applied to calibrate the Low gain settings of the RF3000. As an initial value, the register set-
ting in register 20 should be equal to the value of register 21. Register 20 is provided to allow manufacturing calibration
to account for reverse isolation variances in the T/R switch if used as an additional pad.
Post-AGC
When the Barker code is acquired, the RF3000 assigns the ACQ-bit in the mode register to a 1 and proceeds to extract
the header information. When the start frame delimiter is identified, the RF3000 will assign a 1 to the SFD-bit in the
mode register. The RF3000 will now decode the transmission mode and data length from the header, and check the
header via the 16-bit CRC. The RF3000 will then clock-out 32 bits of header information. This will be the 8-bit RX signal
field, followed by the 8-bit RX service field, and then the 16-bit RX length field. The MAC can also read these values
through the serial port registers 0x04 through 0x07.
The header data will be followed by 16 bit times of no clock transitions.
Immediately before providing data, the RF3000 will drive RX RDY High. The received data will be stable on the rising
edge of DATA CLK
.
In the event the header CRC is incorrect, the RF3000 will bring RX RDY high for the duration of the
packet, but no DATA CLK or RX DATA transitions will occur.
相關PDF資料 |
PDF描述 |
|---|---|
| RF3000PCBA | SPREAD-SPECTRUM BASEBAND MODEM |
| RF2046PCBA-41X | GENERAL PURPOSE AMPLIFIER |
| RF2114 | TRI R RECP F FLG SEAL 0-4 |
| RF2114PCBA | MEDIUM POWER LINEAR AMPLIFIER |
| RF2115 | HIGH POWER UHF AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF-3000 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:SPREAD-SPECTRUM BASEBAND MODEM |
| RF3000PCBA | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:SPREAD-SPECTRUM BASEBAND MODEM |
| RF-3000PCBA | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:SPREAD-SPECTRUM BASEBAND MODEM |
| RF300-12 | 功能描述:高頻/射頻繼電器 12V DC-6GHz .15W RoHS:否 制造商:Omron Electronics 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 VDC 線圈類型:Non-Latching 頻率: 功耗:100 mW 端接類型:Solder Terminal 絕緣:20 dB to 30 dB at 1 GHz 介入損耗:0.2 dB at 1 GHz |
| RF300-12/G | 制造商:Teledyne Relays 功能描述:RF RELAY |
發布緊急采購，3分鐘左右您將得到回復。