- 您現在的位置：買賣IC網 > PDF目錄1962 > PIC10F222-E/OT (Microchip Technology)IC PIC MCU FLASH 512X12 SOT-23-6 PDF資料下載
參數資料
| 型號： | PIC10F222-E/OT |
| 廠商： | Microchip Technology |
| 文件頁數： | 30/86頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PIC MCU FLASH 512X12 SOT-23-6 |
| 標準包裝： | 3,000 |
| 系列： | PIC® 10F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 8MHz |
| 外圍設備： | POR，WDT |
| 輸入/輸出數： | 4 |
| 程序存儲器容量： | 768B（512 x 12） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 23 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2 V ~ 5.5 V |
| 數據轉換器： | A/D 2x8b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | SOT-23-6 |
| 包裝： | 散裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁
PIC10F220/222
DS41270E-page 34
2007 Microchip Technology Inc.
8.2
Oscillator Configurations
8.2.1
OSCILLATOR TYPES
The PIC10F220/222 devices are offered with internal
oscillator mode only.
INTOSC: Internal 4/8 MHz Oscillator
8.2.2
INTERNAL 4/8 MHz OSCILLATOR
The internal oscillator provides a 4/8 MHz (nominal)
system clock (see Section 10.0 “Electrical Charac-
teristics” for information on variation over voltage and
temperature).
In addition, a calibration instruction is programmed into
the last address of memory, which contains the calibra-
tion value for the internal oscillator. This location is
always uncode protected, regardless of the code-pro-
tect settings. This value is programmed as a MOVLW XX
instruction where XX is the calibration value and is
placed at the Reset vector. This will load the W register
with the calibration value upon Reset and the PC will
then roll over to the users program at address 0x000.
The user then has the option of writing the value to the
OSCCAL Register (05h) or ignoring it.
OSCCAL, when written to with the calibration value, will
“trim” the internal oscillator to remove process variation
from the oscillator frequency.
8.3
Reset
The device differentiates between various kinds of
Reset:
Power-on Reset (POR)
MCLR Reset during normal operation
MCLR Reset during Sleep
WDT Time-out Reset during normal operation
WDT Time-out Reset during Sleep
Wake-up from Sleep on pin change
Some registers are not reset in any way, they are
unknown on POR and unchanged in any other Reset.
Most other registers are reset to “Reset state” on
Power-on Reset (POR), MCLR, WDT or Wake-up on
pin change Reset during normal operation. They are
not affected by a WDT Reset during Sleep or MCLR
Reset during Sleep, since these Resets are viewed as
resumption of normal operation. The exceptions to this
are TO, PD and GPWUF bits. They are set or cleared
differently in different Reset situations. These bits are
used in software to determine the nature of Reset. See
Table 8-1 for a full description of Reset states of all
registers.
TABLE 8-1:
RESET CONDITIONS FOR REGISTERS – PIC10F220/222
Note:
Erasing the device will also erase the pre-
programmed internal calibration value for
the internal oscillator. The calibration
value must be read prior to erasing the
part so it can be reprogrammed correctly
later.
Register
Address
Power-on Reset
MCLR Reset, WDT Time-out, Wake-up On Pin Change,
W—
qqqq qqqu
(1)
qqqq qqqu
(1)
INDF
00h
xxxx xxxx
uuuu uuuu
TMR0
01h
xxxx xxxx
uuuu uuuu
PC
02h
1111 1111
STATUS
03h
0--1 1xxx
q00q quuu
FSR
04h
111x xxxx
111u uuuu
OSCCAL
05h
1111 1110
uuuu uuuu
GPIO
06h
---- xxxx
---- uuuu
ADCON0
07h
11-- 1100
ADRES
08h
xxxx xxxx
uuuu uuuu
OPTION
—
1111 1111
TRIS
—
---- 1111
Legend:
u
= unchanged, x = unknown, – = unimplemented bit, read as ‘0’, q = value depends on condition.
Note
1:
Bits <7:2> of W register contain oscillator calibration values due to MOVLW XX instruction at top of memory.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC10F222-I/P | IC PIC MCU FLASH 512X12 8DIP |
| PIC10LF322T-I/OT | MCU 8BIT 896B FLASH SOT23-6 |
| PIC12C508-04I/SM | IC MCU OTP 512X12 8-SOIJ |
| PIC12CE674/JW | IC MCU EPROM 2KX14 A/D&EE 8CDIP |
| PIC12F1840-I/MF | MCU 7KB FLASH 256B RAM 8-DFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC10F222EP | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:6-Pin, 8-Bit Flash Microcontrollers |
| PIC10F222I/MC | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance Microcontrollers with 8-bit A/D |
| PIC10F222-I/MC | 功能描述:8位微控制器 -MCU 0.75KB 23B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC10F222I/OT | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance Microcontrollers with 8-bit A/D |
| PIC10F222-I/OT | 功能描述:8位微控制器 -MCU 768B Flash 23B RAM 4 I/O 8bit ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。