- 您現在的位置：買賣IC網 > PDF目錄1960 > PI2EQX5904NJE (Pericom)IC PCIE 2.0 REDRIVER 100LBGA PDF資料下載
參數資料
| 型號： | PI2EQX5904NJE |
| 廠商： | Pericom |
| 文件頁數： | 20/23頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PCIE 2.0 REDRIVER 100LBGA |
| 標準包裝： | 1 |
| 系列： | PCI Express®(PCIe), ReDriver™ |
| 類型： | 轉接驅動器 |
| 驅動器/接收器數： | 2/2 |
| 規程： | PCIe? 2.0 |
| 電源電壓： | 1.2V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-BGA |
| 供應商設備封裝： | 100-LBGA（11x11） |
| 包裝： | 托盤 |
6
www.pericom.com
PS-0.5
10/18/10
All trademarks are property of their respective owners.
PI2EQX5904
5.0Gbps 4-Lane PCIe 2.0 ReDriver with Equalization & Emphasis
Output Swing Control
S1_[A:B]
S0_[A:B]
Swing (Diff. VPP)
0
1.1V
0
1
0.5V
1
0
0.8V
1
1.0V
Output De-emphasis Adjustment
D2_[A:B]
D1_[A:B]
D0_[A:B]
De-emphasis
0
0dB
0
1
-2.5dB
0
1
0
-3.5dB
0
1
-4.5dB
1
0
-5.5dB
1
0
1
-6.5dB
1
0
-7.5dB
1
-8.5dB
Emphasis settings are determined by the state of the DEx_y input pins and configuration registers, as shown in the Output De-
emphasis table below. De-Emphasis is selected as the default power-on mode in following the PCI Express specification, but can be
changed to Pre-emphasis via reprogramming the Loopback and Emphasis Control register using the I2C interface.
Input Level Detect
An input level detect and output squelch function is provided on each channel to eliminate re-transmission of input noise. A con-
tinuous signal level below the Vth- threshold causes the output driver to go to a high-impredance state, so that both the positive and
negative output signal are pulled to VDD by the internal pull-up resistors. This feature supports the L0s PCI Express Electrical Idle
state.
Receiver Detect
Automatic Receiver Detection is a feature that can set the number of active channels. By sensing the presence of a load device on
the output, the channel can be automatically enabled for operation. This allows the PI2EQX5904 to configure itself properly de-
pending on the devices it is communicating with, whether it is a 4-lane, 3-lane, 2-lane or just 1-lane device or adapter card.
Receiver Detect is enabled by the RXD_A, or RXD_B pins, or alternatively via I2C programming. When RXD_A or RXD_B is set
to low, then the Receiver Detect operation for that group of channel is disabled, and those channels go directly to 50-Ohm input
termination to ground and 50-Ohm output termination to VDD (for a valid differential channel input level) or to 2K-Ohm (if the
signal level is less than the threshold level).
(Continued)
10-0217
相關PDF資料 |
PDF描述 |
|---|---|
| PI2EQX5964ZFE | IC PCIE 2.0 REDRIVER 56TQFN |
| PI2EQX6804-ANJE | IC REDRIVER 100LBGA |
| PI2EQX6864-AZFE | IC REDRIVER 56TQFN |
| PI2LVD412ZHE | IC MUX/DEMUX QUAD 2X1 42TQFN |
| PI2PCIE212ZHEX | IC PCI-E MUX/DEMUX 2X1 28TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PI2EQX5904NJEX | 功能描述:緩沖器和線路驅動器 5.0Gbps 4 lane PCIe 2.0 Redriver RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| PI2EQX5964ZFE | 功能描述:緩沖器和線路驅動器 PCIe 2.0 REDRIVER 5.0Gbps RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| PI2EQX5964ZFEX | 功能描述:緩沖器和線路驅動器 5.0Gbps 4ln PCIe2.0 Redrivr w/I2C config RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| PI2EQX5984ZLE | 功能描述:緩沖器和線路驅動器 4-lane PCIe 2.0 ReDriver RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| PI2EQX5984ZLEX | 功能描述:緩沖器和線路驅動器 4-lane PCIe 2.0 ReDriver RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。