- 您現在的位置：買賣IC網 > PDF目錄1960 > PI2EQX5804CNJE (Pericom)IC PCI-E REDRIVER 100LBGA PDF資料下載
參數資料
| 型號： | PI2EQX5804CNJE |
| 廠商： | Pericom |
| 文件頁數： | 21/23頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PCI-E REDRIVER 100LBGA |
| 標準包裝： | 176 |
| 系列： | ReDriver™ |
| 類型： | 轉接驅動器 |
| Tx/Rx類型： | CML |
| 電容 - 輸入： | 50pF |
| 電源電壓： | 1.15 V ~ 1.25 V |
| 電流 - 電源： | 800mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-BGA |
| 供應商設備封裝： | 100-LBGA（11x11） |
| 包裝： | 托盤 |
7
PS8926B
06/08/09
PI2EQX5804C
5.0Gbps 4-Lane PCIe 2.0 ReDriver with
Equalization & Emphasis
The RESET# input is used to reset the receiver detect state machine to its initial state. The start of the receiver detect
cycle starts when RESET# transitions from low to high.
When a Receiver Detect cycle is begins the differential channel pins are enabled with a 2K-Ohm pullup to VDD. A 50-
Ohm Receiver termination will change the pin level. This pin level is evaluated after a xed time-out, and the channel
is then set into the proper operating state. The output signals RX50_A and RX50_B represent the receiver detect result
for their specic channels.
The I/O Operation table summaries the relationships and operation of receiver detect and other signals involved with
I/O control.
Table 4 - I/O Operation Control
Control Inputs
Detection
States
Data Channel I/O
PD# RXD_x RESET#
RX50
SIG_x Input Termination Output Termination Mode
0
X
Hi-Z
Full IC power down, all channels dis-
abled
1
0
X
Hi-Z
2K-Ohm pull-up
Channel disabled, output pulls to VDD.
Receiver detect reset
10
1
X
0
50-Ohm pull-
down
2K-Ohm pull-up
Channel enabled, no input signal, output
pulls to VDD. Receiver detect disabled
10
1
X
1
50-Ohm pull-
down
50-Ohm pull-up
Channel enabled, valid input signal
detected, output driving. Receiver detect
disabled.
1
0
X
Hi-Z
2K-Ohm pull-up
Channel disabled. Receiver detect reset.
1
0
X
Hi-Z
2K-Ohm pull-up
Channel disabled, output pulls to VDD.
Receiver detect enabled, no receiver
detected.
11
1
0
50-Ohm pull-
down
2K-Ohm pull-up
Channel inactive, output pulls to VDD.
Receiver detect enabled, receiver de-
tected. No input signal
11
1
50-Ohm pull-
down
50-Ohm pull-up
Channel active, valid input signal de-
tected, output driving. Receiver detect
enabled, load detected.
09-0001
相關PDF資料 |
PDF描述 |
|---|---|
| PI2EQX5864CZFE | IC PCI-E REDRIVER 56TQFN |
| PI2EQX5904NJE | IC PCIE 2.0 REDRIVER 100LBGA |
| PI2EQX5964ZFE | IC PCIE 2.0 REDRIVER 56TQFN |
| PI2EQX6804-ANJE | IC REDRIVER 100LBGA |
| PI2EQX6864-AZFE | IC REDRIVER 56TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PI2EQX5804CNJEX | 功能描述:緩沖器和線路驅動器 PCI-Express Gen-2 5.0Gbps RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| Pi2EQX5804DNJE | 功能描述:緩沖器和線路驅動器 RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| PI2EQX5804DNJEX | 功能描述:緩沖器和線路驅動器 5.0Gbps 4 lane PCIe 2.0 Redriver RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| PI2EQX5864 | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:5.0Gbps 4-Lane PCI Express GenII Re-Driver with Equalization, Emphasis, &I2C Control |
| PI2EQX5864CZFE | 功能描述:緩沖器和線路驅動器 PCI express Gen-2 5.0Gbps RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。