- 您現在的位置：買賣IC網 > PDF目錄296796 > PCM9211PT (TEXAS INSTRUMENTS INC) DATACOM, TOKEN RING TRANSCEIVER, PQFP48 PDF資料下載
參數資料
| 型號： | PCM9211PT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 網絡接口 |
| 英文描述： | DATACOM, TOKEN RING TRANSCEIVER, PQFP48 |
| 封裝： | GREEN, PLASTIC, LQFP-48 |
| 文件頁數： | 30/121頁 |
| 文件大?。?/td> | 1219K |
| 代理商： | PCM9211PT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁
RST
MODE
V
DD
Tied to V
or DGND
DD
V
= 2.2 V typ
DD
V
= 3.3 V typ
DD
0 V
t
RSTL
SBAS495 – JUNE 2010
www.ti.com
PCM9211 MODULE DESCRIPTIONS
Power Supply
The PCM9211 has four power-supply pins and four ground pins. All ground pins (AGND, AGNDAD, DGND, and
GNDRX) must be connected as closely as possible to the PCM9211. The PCM9211 DVDD and DGND pins are
power-supply pins that support all the onboard digital circuitry for the PCM9211. DVDD should be connected to a
3.3-V supply. DVDD drives the internal power-on reset circuit, making it a startup requirement.
VCC and AGND are analog power-supply power pins that support the DIR analog supply rails.
VDDAD and AGNDAD are dedicated power-supply pins for the onboard ADC. VDDAD should be connected to a
5.0-V power rail.
VDDRX is a dedicated power supply for the coaxial input amplifiers on pins RXIN0 and RXIN1. It should be
connected to a 3.3-V pin. The relative GND pin for this supply is GNDRX. If the coaxial amplifiers are not used
(for example, the application only uses optical inputs), then no power supply is required for the VDDRX.
If the onboard ADC is not used (such as when the application uses an external ADC) then no power supply is
required for the VCCAD pin. This option means that a 5-V rail is not required when the internal ADC is not used.
In such situations, VCCAD should be connected to AGND OR AGNDAD.
Because VCC (3.3 V) is an analog supply (used as part of the power supply for the DIR PLL), care should be
taken to ensure minimum noise and ripple are present. 0.1-mF ceramic capacitors and 10-mF electrolytic
capacitors should be used to decouple each supply pin to the respective relative GND (for example, to decouple
VCCAD and AGNDAD).
Power-Down Function
The PCM9211 has a power-down function that is controlled by the external RST pin or a power control register.
When the RST pin is held at GND, the PCM9211 powers down.
When the device is powered down (that is, RST = GND), all register values are cleared and reset to the
respective default values. By default, all modules are powered on except for the coaxial amplifier.
The other option for powering down the device is to use the Power Control Register (Register 40h). The Power
Control Register allows selective power down of the DIR, ADC, DIT, Coax Amp, and Oscillator circuit without
resetting other registers to the respective default modes.
The advantage of using the registers to power down individual modules of the PCM9211 is that the registers
retain the respective settings rather than resetting to default.
System Reset
The PCM9211 has two sources for reset: the internal power-on reset circuit (hereafter called POR) and the
external reset circuit. See Figure 14 for an illustration of the timing sequence during an internal power-on reset
event. Initialization (reset) is done automatically when VDD exceeds 2.2 V (typ).
When only the onboard POR is to be used, the RST pin should be connected to VDD directly. An external pull-up
resistor should not be used, because the RST pin has an internal pull-down resistor (typ 50 k
Ω). If an external
resistor is used, then the reset is not released. The reset sequence is shown in Figure 11.
Figure 11. Required System Reset Timing
16
Copyright 2010, Texas Instruments Incorporated
Product Folder Link(s): PCM9211
相關PDF資料 |
PDF描述 |
|---|---|
| PCN11MF | STRIP TERMINAL BLOCK, 1 DECK |
| PCN12E-32S-2.54DSA | 32 CONTACT(S), FEMALE, STRAIGHT TWO PART EURO CONNECTOR, SOLDER, SOCKET |
| PCN12E-44S-2.54DSA | 44 CONTACT(S), FEMALE, STRAIGHT TWO PART EURO CONNECTOR, SOLDER, SOCKET |
| PCN12E-50S-2.54DSA | 50 CONTACT(S), FEMALE, STRAIGHT TWO PART EURO CONNECTOR, SOLDER, SOCKET |
| PCR-E68LMD | 68 CONTACT(S), MALE, RIGHT ANGLE TELECOM AND DATACOM CONNECTOR, SOLDER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCM9211PTR | 功能描述:音頻發送器、接收器、收發器 216kHz Dig Aud Inter face Transceiver RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝: |
| PCM-93 | 功能描述:電線鑒定 Pre-Printed WM Card, Vinyl Cloth, .22" W RoHS:否 制造商:TE Connectivity / Q-Cees 產品:Labels and Signs 類型: 材料:Vinyl 顏色:Blue 寬度:0.625 in 長度:1 in |
| PCM-9342 | 制造商:ADVANTECH 制造商全稱:Advantech Co., Ltd. 功能描述:X86 SoC 3.5" SBC with VGA, LCD, LAN, USB, SATA, CF, PC/104 |
| PCM-9342F-64A1E | 制造商:ADVANTECH 制造商全稱:Advantech Co., Ltd. 功能描述:X86 SoC 3.5" SBC with VGA, LCD, LAN, USB, SATA, CF, PC/104 |
| PCM-9342FZ2-64A1E | 制造商:ADVANTECH 制造商全稱:Advantech Co., Ltd. 功能描述:X86 SoC 3.5" SBC with VGA, LCD, LAN, USB, SATA, CF, PC/104 |
發布緊急采購，3分鐘左右您將得到回復。