參數資料
型號： PCF85176T
廠商： NXP SEMICONDUCTORS
元件分類： 顯示驅動器
英文描述： Universal LCD driver for low multiplex rates
中文描述： LIQUID CRYSTAL DISPLAY DRIVER, PDSO56
封裝： 6.10 MM, PLASTIC, MO-153, SOT364-1, TSSOP-56
文件頁數： 16/47頁
文件大?。?/td> 405K
代理商： PCF85176T
PCF85176
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 27 June 2011
16 of 47
NXP Semiconductors
PCF85176
Universal LCD driver for low multiplex rates
7.5 Oscillator
7.5.1
Internal clock
The internal logic of the PCF85176 and its LCD drive signals are timed either by its
internal oscillator or by an external clock. The internal oscillator is enabled by connecting
pin OSC to pin V
SS
. If the internal oscillator is used, the output from pin CLK can be used
as the clock signal for several PCF85176 in the system that are connected in cascade.
7.5.2
External clock
Pin CLK is enabled as an external clock input by connecting pin OSC to V
DD
. The LCD
frame signal frequency is determined by the clock frequency (f
clk
).
Remark:
A clock signal must always be supplied to the device; removing the clock may
freeze the LCD in a DC state, which is not suitable for the liquid crystal.
7.6 Timing
The PCF85176 timing controls the internal data flow of the device. This includes the
transfer of display data from the display RAM to the display segment outputs. In cascaded
applications, the correct timing relationship between each PCF85176 in the system is
maintained by the synchronization signal at pin SYNC. The timing also generates the LCD
frame signal whose frequency is derived from the clock frequency. The frame signal
frequency is a fixed division of the clock frequency from either the internal or an external
f
24
clock:
7.7 Display register
The display register holds the display data while the corresponding multiplex signals are
generated.
7.8 Segment outputs
The LCD drive section includes 40 segment outputs S0 to S39 which should be
connected directly to the LCD. The segment output signals are generated in accordance
with the multiplexed backplane signals and with data residing in the display register. When
less than 40 segment outputs are required, the unused segment outputs should be left
open-circuit.
7.9 Backplane outputs
The LCD drive section includes four backplane outputs BP0 to BP3 which must be
connected directly to the LCD. The backplane output signals are generated in accordance
with the selected LCD drive mode. If less than four backplane outputs are required, the
unused outputs can be left open-circuit.
In 1:3 multiplex drive mode, BP3 carries the same signal as BP1, therefore these two
adjacent outputs can be tied together to give enhanced drive capabilities.
In 1:2 multiplex drive mode, BP0 and BP2, respectively, BP1 and BP3 all carry the
same signals and may also be paired to increase the drive capabilities.
f
fr
-------
=
相關PDF資料
PDF描述
PCF8574AT Remote 8-bit I-O expander for I2C-bus
PCF8574P Remote 8-bit I-O expander for I2C-bus
PCF8574T Remote 8-bit I-O expander for I2C-bus
PCH1632 CHIP TYPE IMPEDANCE CONVERTER
PCH163250B CHIP TYPE IMPEDANCE CONVERTER
相關代理商/技術參數
參數描述
PCF85176T/1,118 功能描述:LCD 驅動器 40 SGMT 2640Hz RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
PCF8522EP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM
PCF8522ET 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM
PCF8523 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Real-Time Clock (RTC) and calendar
PCF8523T 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Save power with small, ultra-efficient RTCs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*