- 您現在的位置：買賣IC網 > PDF目錄367749 > PA28F008S5-85 (INTEL CORP) BYTE-WIDE SMART 5 FlashFile MEMORY FAMILY 4, 8, AND 16 MBIT PDF資料下載
參數資料
| 型號： | PA28F008S5-85 |
| 廠商： | INTEL CORP |
| 元件分類： | PROM |
| 英文描述： | BYTE-WIDE SMART 5 FlashFile MEMORY FAMILY 4, 8, AND 16 MBIT |
| 中文描述： | 1M X 8 FLASH 5V PROM, 85 ns, PDSO44 |
| 封裝： | 13.30 X 28.20 MM, PLASTIC, SOP-44 |
| 文件頁數： | 10/37頁 |
| 文件大?。?/td> | 611K |
| 代理商： | PA28F008S5-85 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
BYTE-WIDE SMART 5 FlashFile MEMORY FAMILY
E
10
PRODUCT PREVIEW
2.1
Data Protection
Depending on the application, the system designer
may choose to make the V
PP
power supply
switchable (available only when memory block
erases, programs, or lock-bit configurations are
required) or hardwired to V
PPH1/2
. The device
accommodates
either
encourages optimization of the processor-memory
interface.
design
practice
and
When V
PP
≤
V
PPLK
, memory contents cannot be
altered. When high voltage is applied to V
PP
, the
two-step
block
erase,
configuration command sequences provides pro-
tection from unwanted operations. All write
functions are disabled when V
CC
voltage is below
the write lockout voltage V
LKO
or when RP# is at
V
IL
. The device’s block locking capability provides
additional protection from inadvertent code or data
alteration by gating erase and program operations.
program,
or
lock-bit
3.0
BUS OPERATION
The local CPU reads and writes flash memory
in-system. All bus cycles to or from the flash
memory conform to standard microprocessor bus
cycles.
3.1
Read
Block information, identifier codes, or status register
can be read independent of the V
PP
voltage. RP#
can be at either V
IH
or V
HH
.
The first task is to write the appropriate read-mode
command (Read Array, Read Identifier Codes, or
Read Status Register) to the CUI. Upon initial
device power-up or after exit from deep power-
down mode, the device automatically resets to read
array mode. Four control pins dictate the data flow
in and out of the component: CE#, OE#, WE#, and
RP#. CE# and OE# must be driven active to obtain
data at the outputs. CE# is the device selection
control, and when active enables the selected
memory device. OE# is the data output (DQ
0
–DQ
7
)
control and when active drives the selected
memory data onto the I/O bus. WE# must be at V
IH
and RP# must be at V
IH
or V
HH
. Figure 15
illustrates a read cycle.
3.2
Output Disable
With OE# at a logic-high level (V
), the device
outputs are disabled. Output pins DQ
0
–DQ
7
are
placed in a high-impedance state.
3.3
Standby
CE# at a logic-high level (V
) places the device in
standby mode which substantially reduces device
power consumption. DQ
0
–DQ
7
outputs are placed
in a high-impedance state independent of OE#. If
deselected during block erase, program, or
lock-bit
configuration,
functioning and consuming active power until the
operation completes.
the
device
continues
3.4
Deep Power-Down
RP# at V
IL
initiates the deep power-down mode.
In read mode, RP#-low deselects the memory,
places output drivers in a high-impedance state,
and turns off all internal circuits. RP# must be held
low for time t
PLPH
. Time t
PHQV
is required after
return from power-down until initial memory access
outputs are valid. After this wake-up interval,
normal operation is restored. The CUI resets to
read array mode, and the status register is set to
80H.
During
configuration, RP#-low will abort the operation.
RY/BY# remains low until the reset operation is
complete. Memory contents being altered are no
longer valid; the data may be partially erased or
written. Time t
PHWL
is required after RP# goes to
logic-high (V
IH
) before another command can be
written.
block
erase,
program,
or
lock-bit
As with any automated device, it is important to
assert RP# during system reset. When the system
comes out of reset, it expects to read from the flash
memory. Automated flash memories provide status
information when accessed during block erase,
program, or lock-bit configuration modes. If a CPU
reset occurs with no flash memory reset, proper
CPU initialization may not occur because the flash
memory may be providing status information
instead of array data. Intel’s flash memories allow
proper CPU initialization following a system reset
through the use of the RP# input. In this application,
RP# is controlled by the same RESET# signal that
resets the system CPU.
相關PDF資料 |
PDF描述 |
|---|---|
| PA28F004S5-85 | BYTE-WIDE SMART 5 FlashFile MEMORY FAMILY 4, 8, AND 16 MBIT |
| PA28F008S5-120 | BYTE-WIDE SMART 5 FlashFile MEMORY FAMILY 4, 8, AND 16 MBIT |
| PA28F016SC-95 | BYTE-WIDE SmartVoltage FlashFile⑩ MEMORY FAMILY 4, 8, AND 16 MBIT |
| PA28F004SC-120 | BYTE-WIDE SmartVoltage FlashFile MEMORY FAMILY 4, 8, AND 16 MBIT |
| PA28F004SC-85 | BYTE-WIDE SmartVoltage FlashFile MEMORY FAMILY 4, 8, AND 16 MBIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PA28F008SA-120 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:8-MBIT (1-MBIT x 8) FlashFileTM MEMORY |
| PA28F008SA85 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intel 功能描述: |
| PA28F008SA-85 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:8-MBIT (1-MBIT x 8) FlashFileTM MEMORY |
| PA28F008SA-L200 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| PA28F008SA-L250 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
發布緊急采購，3分鐘左右您將得到回復。