- 您現在的位置：買賣IC網 > PDF目錄299575 > OR3C804BA352-DB (LATTICE SEMICONDUCTOR CORP) FPGA, 484 CLBS, 116000 GATES, PBGA352 PDF資料下載
參數資料
| 型號： | OR3C804BA352-DB |
| 廠商： | LATTICE SEMICONDUCTOR CORP |
| 元件分類： | FPGA |
| 英文描述： | FPGA, 484 CLBS, 116000 GATES, PBGA352 |
| 封裝： | PLASTIC, BGA-352 |
| 文件頁數： | 185/203頁 |
| 文件大?。?/td> | 1368K |
| 代理商： | OR3C804BA352-DB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁當前第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁
82
Lattice Semiconductor
Data Sheet
November 2006
ORCA Series 3C and 3T FPGAs
Programmable Clock Manager (PCM)
(continued)
High-Speed Internal Processing with Slow I/Os
The PCM PLL mode provides two outputs, one sent to
the global system clock routing of the FPGA and the
other to the ExpressCLK(s) that serve the FPGA I/Os.
The ExpressCLK output of the PCM has a divide capa-
bility (DIV2) that the system clock output does not. This
feature allows an input clock to be multiplied up to a
higher frequency for high-speed internal processing,
and also allows the ExpressCLK output to be divided
down to a lower frequency to accommodate off-FPGA
data transfers. For example, a 10 MHz input clock may
be multiplied (see Clock Multiplication in the Phase-
Locked Loop (PLL) Mode subsection) to 25 MHz (DIV0
= 4, DIV1 = 5, DIV2 = 2) and output to the FPGA
ExpressCLK
. This allows the I/Os of the circuit to run at
25 MHz ((2 * 5)/4 * 10 MHz). The system clock will run
at DIV2 times the ExpressCLK rate, which is 2 times
25 MHz, or 50 MHz. This setup allows for internal pro-
cessing to occur at twice the rate of on/off device I/O
transfers.
PCM Cautions
Cautions do apply when using the PCM. There are a
number of congurations that are possible in the PCM
that are theoretically valid, but may not produce viable
results. This section describes some of those situa-
tions, and should leave the user with an understanding
of the types of pitfalls that must be avoided when modi-
fying clock signals.
Resultant signals from the PCM must meet the FPGA
timing specications. It is possible to specify pulses by
using duty-cycle adjustments that are too narrow to
function in the FPGA. For instance, if a 40 MHz clock is
doubled to 80 MHz and a 6.25% duty cycle is selected,
the result will be a 780 ps pulse that repeats every
12.5 ns. This pulse falls outside of the clock pulse width
specication and is not valid.
Using divider DIV2, it is possible to specify a clock mul-
tiplication factor of 64 between the input clock and the
output system clock. As mentioned above, the resultant
frequency must meet all FPGA timing specications.
The input clock must also meet the minimum specica-
tions. An input clock rate that is below the PCM clock
minimum cannot be used even if the multiplied output is
within the allowable range.
The use of the PCM to tweak a clock signal to eliminate
a particular problem, such as a single setup time viola-
tion, is discouraged. A small shift in delay, duty cycle, or
phase to correct a single-point problem is in essence
an asynchronous patch to a synchronous system, mak-
ing the system less stable. This type of local problem,
as opposed to a global clock control issue like device-
wide clock delay, can usually be eliminated through
more robust design practices. If this type of change is
made, the designer must be aware that depending on
the extent of the change made, the design may fail to
operate correctly in a different speed grade or voltage
grade (e.g., 3C vs. 3T), or even in a different production
lot of the same device.
Divider DIV2 is available in DLL mode for the Express-
CLK
output, but its use is not recommended with duty-
cycle adjusted clocks.
Select
devices
have
been
discontinued.
See
Ordering
Information
section
for
product
status.
相關PDF資料 |
PDF描述 |
|---|---|
| OR3C804PS208-DB | FPGA, 484 CLBS, 116000 GATES, PQFP208 |
| OR3T1256PS208I-DB | FPGA, 784 CLBS, 186000 GATES, PQFP208 |
| OR3T1256PS240-DB | FPGA, 784 CLBS, 186000 GATES, PQFP240 |
| OR3T1256PS240I-DB | FPGA, 784 CLBS, 186000 GATES, PQFP240 |
| OR3T1257PS208-DB | FPGA, 784 CLBS, 186000 GATES, PQFP208 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OR3C80-4BA352I | 制造商:AGERE 制造商全稱:AGERE 功能描述:3C and 3T Field-Programmable Gate Arrays |
| OR3C804BA352I-DB | 功能描述:FPGA - 現場可編程門陣列 3872 LUT 356 I/O RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256 |
| OR3C80-4BC432 | 制造商:AGERE 制造商全稱:AGERE 功能描述:3C and 3T Field-Programmable Gate Arrays |
| OR3C80-4BC432I | 制造商:AGERE 制造商全稱:AGERE 功能描述:3C and 3T Field-Programmable Gate Arrays |
| OR3C80-4BC600I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
發布緊急采購，3分鐘左右您將得到回復。