- 您現在的位置：買賣IC網 > PDF目錄361112 > NE5230DG (ON SEMICONDUCTOR) Low Voltage Operational Amplifier PDF資料下載
參數資料
| 型號： | NE5230DG |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 運算放大器 |
| 英文描述： | Low Voltage Operational Amplifier |
| 中文描述： | OP-AMP, 4000 uV OFFSET-MAX, 0.6 MHz BAND WIDTH, PDSO8 |
| 封裝： | LEAD FREE, PLASTIC, SOIC-8 |
| 文件頁數： | 8/18頁 |
| 文件大?。?/td> | 253K |
| 代理商： | NE5230DG |
NE5230, SA5230, SE5230
http://onsemi.com
8
THERMAL CONSIDERATIONS
When using the NE5230, the internal power dissipation
capabilities of each package should be considered.
ON Semiconductor does not recommend operation at die
temperatures above 110
°
C in the SO package because of its
inherently smaller package mass. Die temperatures of
150
°
C can be tolerated in all the other packages. With this
in mind, the following equation can be used to estimate the
die temperature:
Tj
Tamb
(PD
JA)
(eq. 1)
Where
T
amb
= Ambient Temperature
T
j
= Die Temperature
P
D
= Power Dissipation
= (I
CC
x V
CC
)
JA
= Package Thermal Resistance
= 270
°
C/W for SO
8 in PC Board Mounting
See the packaging section for information regarding other
methods of mounting.
JA
100
°
C/W for the plastic DIP.
The maximum supply voltage for the part is 15 V and the
typical supply current is 1.1 mA (1.6 mA max). For
operation at supply voltages other than the maximum, see
the data sheet for I
CC
versus V
CC
curves. The supply current
is somewhat proportional to temperature and varies no more
than 100 A between 25
°
C and either temperature extreme.
Operation at higher junction temperatures than that
recommended is possible but will result in lower Mean Time
Between Failures (MTBF). This should be considered
before operating beyond recommended die temperature
because of the overall reliability degradation.
DESIGN TECHNIQUES AND APPLICATIONS
The NE5230 is a very user
friendly amplifier for an
engineer to design into any type of system. The supply
current adjust pin (Pin 5) can be left open or tied through a
pot or fixed resistor to the most negative supply (i.e., ground
for single supply or to the negative supply for split supplies).
The minimum supply current is achieved by leaving this pin
open. In this state it will also decrease the bandwidth and
slew rate. When tied directly to the most negative supply, the
device has full bandwidth, slew rate and I
CC
. The
programming of the current
control pin depends on the
trade
offs which can be made in the designer’s application.
The graphs in Figures 3 and 4 will help by showing
bandwidth versus I
CC
. As can be seen, the supply current can
be varied anywhere over the range of 100 A to 600 A for
a supply voltage of 1.8 V. An external resistor can be
inserted between the current control pin and the most
negative supply. The resistor can be selected between 1.0
to 100 k to provide any required supply current over the
indicated range. In addition, a small varying voltage on the
bias current control pin could be used for such exotic things
as changing the gain
bandwidth for voltage controlled low
pass filters or amplitude modulation. Furthermore, control
over the slew rate and the rise time of the amplifier can be
obtained in the same manner. This control over the slew rate
also changes the settling time and overshoot in pulse
response applications. The settling time to 0.1% changes
from 5.0 s at low bias to 2.0 s at high bias. The supply
current control can also be utilized for wave
shaping
applications such as for pulse or triangular waveforms. The
gain
bandwidth can be varied from between 250 kHz at low
bias to 600 kHz at high bias current. The slew rate range is
0.08 V/ s at low bias and 0.25 V/ s at high bias.
Figure 3. Unity Gain Bandwidth vs. Power Supply
Current for V
CC
=
±
0.9 V
Figure 4. I
CC
Current vs. Bias Current Adjusting
Resistor for Several Supply Voltages
800
700
600
500
400
300
200
100
100
200
300
400 500 600700
UNITY GAIN BANDWIDTH (kHz)
T
A
25
°
C
V
CC
15V
V
CC
12V
V
CC
9V
V
CC
6V
V
CC
3V
V
CC
2V
V
CC
1.8V
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.010
0
10
1
10
2
R
ADJ
( )
10
3
10
4
10
5
P
I
C
相關PDF資料 |
PDF描述 |
|---|---|
| NE5500179A | SILICON POWER MOS FET |
| NE5500179A-T1 | SILICON POWER MOS FET |
| NE5510179A | 3.5V OPERATION SILICON RF POWER MOSFET FOR 1.9 GHZ TRANSMISSION AMPLIFIERS |
| NE5510179A-T1 | 3.5V OPERATION SILICON RF POWER MOSFET FOR 1.9 GHZ TRANSMISSION AMPLIFIERS |
| NE5511279A | NECS 7.5 V UHF BAND RF POWER SILICON LD-MOS FET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NE5230DR2 | 功能描述:運算放大器 - 運放 1.8V Single Rail to RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| NE5230DR2G | 功能描述:運算放大器 - 運放 1.8V Single Rail to Rail Commercial Temp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| NE5230N | 功能描述:運算放大器 - 運放 1.8V Single Rail to RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| NE5230NG | 功能描述:運算放大器 - 運放 1.8V Single Rail to Rail Commercial Temp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| NE5232 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Matched dual high-performance low-voltage operational amplifier |
發布緊急采購，3分鐘左右您將得到回復。