- 您現在的位置：買賣IC網 > PDF目錄39600 > MK2058-01SILF OTHER CLOCK GENERATOR, PDSO20 PDF資料下載
參數資料
| 型號： | MK2058-01SILF |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | OTHER CLOCK GENERATOR, PDSO20 |
| 封裝： | 0.300 INCH, SOIC-20 |
| 文件頁數： | 7/10頁 |
| 文件大?。?/td> | 164K |
| 代理商： | MK2058-01SILF |
Communications Clock Jitter Attenuator
MDS 2058-01 C
6
Revision 050803
Integrated Circuit Systems, Inc. ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ●
www.icst.com
MK2058-01
process, it is important to keep stray capacitance to a
minimum by using very short PCB traces (and no via’s)
been the crystal and device.
In most cases the load capacitors will not be required.
They should not be stuffed on the prototype evaluation
board as the indiscriminate use of these trim capacitors
will typically cause more crystal centering error than
their absence. If the need for the load capacitors is later
determined, the values will fall within the 1-4 pf range.
The need for, and value of, these trim capacitors can
only be determined at prototype evaluation. Please
refer to MAN05 for the procedure to determine the
component values.
PCB Layout Recommendations
For optimum device performance and lowest output
phase noise, the following guidelines should be
observed. Please also refer to the Recommended PCB
Layout drawing on Page 7.
1) Each 0.01F decoupling capacitor should be
mounted on the component side of the board as close
to the VDD pin as possible. No vias should be used
between decoupling capacitor and VDD pin. The PCB
trace to VDD pin should be kept as short as possible,
as should the PCB trace to the ground via. Distance of
the ferrite bead and bulk decoupling from the device is
less critical.
2) The loop filter components must also be placed
close to the CHGP and VIN pins. CP should be closest
to the device. Coupling of noise from other system
signal traces should be minimized by keeping traces
short and away from active signal traces. Use of vias
should be avoided.
3) The external crystal should be mounted just next to
the device with short traces. The X1 and X2 traces
should not be routed next to each other with minimum
spaces, instead they should be separated and away
from other traces.
4) To minimize EMI the 33
W series termination resistor,
if needed, should be placed close to the clock output.
5) An optimum layout is one with all components on the
same side of the board, minimizing vias through other
signal layers (the ferrite bead and bulk decoupling
capacitor can be mounted on the back). Other signal
traces should be routed away from the MK2058-01.
This includes signal traces just underneath the device,
or on layers adjacent to the ground plane layer used by
the device.
The ICS Applications Note MAN05 may also be
referenced for additional suggestions on layout of the
crystal section.
相關PDF資料 |
PDF描述 |
|---|---|
| MK2704SLF | 36.864 MHz, VIDEO CLOCK GENERATOR, PDSO8 |
| MK2704SLFTR | 36.864 MHz, VIDEO CLOCK GENERATOR, PDSO8 |
| MK2704STR | 36.864 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| MK2704SLFTR | 36.864 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| MK2714STR | 74.17582418 MHz, VIDEO CLOCK GENERATOR, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MK2058-01SILFTR | 功能描述:時鐘合成器/抖動清除器 COMMUNICATIONS CLOCK JITTER ATTENUATOR RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| MK205801SITR | 制造商:Integrated Device Technology Inc 功能描述: |
| MK2058-01SITR | 功能描述:IC VCXO CLK JITTER ATTEN 20-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| MK2059-01 | 制造商:ICS 制造商全稱:ICS 功能描述:VCXO-Based Frame Clock Frequency Translator |
| MK2059-01SI | 功能描述:IC VCXO CLK JITTER ATTEN 20-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
發布緊急采購，3分鐘左右您將得到回復。