- 您現在的位置：買賣IC網 > PDF目錄65810 > MK1581-01GILF 2.048 MHz, OTHER CLOCK GENERATOR, PDSO16 PDF資料下載
參數資料
| 型號： | MK1581-01GILF |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 2.048 MHz, OTHER CLOCK GENERATOR, PDSO16 |
| 封裝： | 4.40 MM, 0.65 MM PITCH, MO-153, TSSOP-16 |
| 文件頁數： | 7/10頁 |
| 文件大?。?/td> | 152K |
| 代理商： | MK1581-01GILF |
Low Phase Noise T1 / E1 Clock Generator
MDS 1581-01 C
6
Revision 050803
Integrated Circuit Systems, Inc. ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ●
www.icst.com
MK1581-01
required crystal load capacitance. Because load
capacitance can only be increased in this trimming
process, it is important to keep stray capacitance to a
minimum by using very short PCB traces (and no vias)
been the crystal and device.
In most cases the load capacitors will not be required.
They should not be stuffed on the prototype evaluation
board as the indiscriminate use of these trim capacitors
will typically cause more crystal centering error than
their absence. If the need for the load capacitors is later
determined, the values will fall within the 1-4 pf range.
The need for, and value of, these trim capacitors can
only be determined at prototype evaluation. Refer to
MAN05 for the centering capacitor selection procedure.
PCB Layout Recommendations
For optimum device performance and lowest output
phase noise, the following guidelines should be
observed. Please also refer to the Recommended PCB
Layout drawing on Page 7.
1) Each 0.01F decoupling capacitor should be
mounted on the component side of the board as close
to the VDD pin as possible. No via’s should be used
between decoupling capacitor and VDD pin. The PCB
trace to VDD pin should be kept as short as possible,
as should the PCB trace to the ground via. Distance of
the ferrite bead and bulk decoupling from the device is
less critical.
2) The loop filter components must also be placed
close to the CHGP and VIN pins. CP should be closest
to the device. Coupling of noise from other system
signal traces should be minimized by keeping traces
short and away from active signal traces. Use of vias
should be avoided.
3) The external crystal should be mounted just next to
the device with short traces. The X1 and X2 traces
should not be routed next to each other with minimum
spaces, instead they should be separated and away
from other traces.
4) To minimize EMI the 33
W series termination resistor,
if needed, should be placed close to the clock output.
5) An optimum layout is one with all components on the
same side of the board, minimizing vias through other
signal layers (the ferrite bead and bulk decoupling
capacitor can be mounted on the back). Other signal
traces should be routed away from the MK1581-01.
This includes signal traces just underneath the device,
or on layers adjacent to the ground plane layer used by
the device.
The ICS Applications Note MAN05 may also be
referenced for additional suggestions on layout of the
crystal section.
相關PDF資料 |
PDF描述 |
|---|---|
| MK1581-01GITR | 2.048 MHz, OTHER CLOCK GENERATOR, PDSO16 |
| MK1581-01GI | 2.048 MHz, OTHER CLOCK GENERATOR, PDSO16 |
| MK1704A | 140 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| MK1705A | 167 MHz, VIDEO CLOCK GENERATOR, PDSO8 |
| MK1705ALFTR | 167 MHz, VIDEO CLOCK GENERATOR, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MK1581-01GILFTR | 功能描述:時鐘發生器及支持產品 LOW PHASE NOISE T1/E 1 CLOCK GENERATOR RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| MK1581-01GITR | 功能描述:IC CLK GENERATOR T1/E1 16-TSSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| MK159 | 制造商:Velleman Inc 功能描述:Brain Game Kit |
| MK15-B-0 | 制造商:MEDER 制造商全稱:Meder Electronic 功能描述:MK Reed Sensors |
| MK15-B-0_DE | 制造商:MEDER 制造商全稱:Meder Electronic 功能描述:(deutsch) MK Reed Sensor |
發布緊急采購，3分鐘左右您將得到回復。