- 您現在的位置：買賣IC網 > PDF目錄4051 > MC8610VT800GB (Freescale Semiconductor)MPU E600 CORE 800MHZ 783-PBGA PDF資料下載
參數資料
| 型號： | MC8610VT800GB |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 79/96頁 |
| 文件大小： | 0K |
| 描述： | MPU E600 CORE 800MHZ 783-PBGA |
| 標準包裝： | 36 |
| 系列： | MPC86xx |
| 處理器類型： | 32-位 MPC86xx PowerPC |
| 速度： | 800MHz |
| 電壓： | 1V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 783-BBGA，F(xiàn)CBGA |
| 供應商設備封裝： | 783-FCPBGA（29x29） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁當前第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
MPC8610 Integrated Host Processor Hardware Specifications, Rev. 2
Hardware Design Considerations
Freescale Semiconductor
80
3.9
JTAG Configuration Signals
Correct operation of the JTAG interface requires configuration of a group of system control pins as demonstrated in Figure 53.
Care must be taken to ensure that these pins are maintained at a valid deasserted state under normal operating conditions as most
have asynchronous behavior and spurious assertion will give unpredictable results.
Boundary-scan testing is enabled through the JTAG interface signals. The TRST signal is optional in the IEEE 1149.1
specification, but is provided on all processors that implement the Power Architecture technology. The device requires TRST
to be asserted during reset conditions to ensure the JTAG boundary logic does not interfere with normal chip operation. While
it is possible to force the TAP controller to the reset state using only the TCK and TMS signals, more reliable power-on reset
performance will be obtained if the TRST signal is asserted during power-on reset. Because the JTAG interface is also used for
accessing the common on-chip processor (COP) function, simply tying TRST to HRESET is not practical.
The COP function of these processors allows a remote computer system (typically a PC with dedicated hardware and debugging
software) to access and control the internal operations of the processor. The COP port connects primarily through the JTAG
interface of the processor, with some additional status monitoring signals. The COP port requires the ability to independently
assert HRESET or TRST in order to fully control the processor. If the target system has independent reset sources, such as
voltage monitors, watchdog timers, power supply failures, or push-button switches, then the COP reset signals must be merged
into these signals with logic.
The arrangement shown in Figure 52 allows the COP port to independently assert HRESET or TRST, while ensuring that the
target can drive HRESET as well.
The COP interface has a standard header, shown in Figure 52, for connection to the target system, and is based on the 0.025"
square-post, 0.100" centered header assembly (often called a Berg header). The connector typically has pin 14 removed as a
connector key.
The COP header adds many benefits such as breakpoints, watchpoints, register and memory examination/modification, and
other standard debugger features. An inexpensive option can be to leave the COP header unpopulated until needed.
There is no standardized way to number the COP header shown in Figure 53; consequently, many different pin numbers have
been observed from emulator vendors. Some are numbered top-to-bottom then left-to-right, while others use left-to-right then
top-to-bottom, while still others number the pins counter clockwise from pin 1 (as with an IC). Regardless of the numbering,
the signal placement recommended in Figure 53 is common to all known emulators.
3.9.1
Termination of Unused Signals
If the JTAG interface and COP header will not be used, Freescale recommends the following connections:
TRST should be tied to HRESET through a 0-k
Ω isolation resistor so that it is asserted when the system reset signal
(HRESET) is asserted, ensuring that the JTAG scan chain is initialized during the power-on reset flow. Freescale
recommends that the COP header be designed into the system as shown in Figure 53. If this is not possible, the
isolation resistor will allow future access to TRST in case a JTAG interface may need to be wired onto the system in
future debug situations.
Tie TCK to OVDD through a 10-kΩ resistor. This will prevent TCK from changing state and reading incorrect data
into the device.
No connection is required for TDI, TMS, or TDO.
相關PDF資料 |
PDF描述 |
|---|---|
| MPC8536CVTANGA | MPU POWERQUICC III 783FCPBGA |
| MPC755CVT350LE | MCU HIP4DP 350MHZ 360-PBGA |
| MPC755CRX350LE | MCU HIP4DP 350MHZ 360-CBGA |
| MPC755CPX350LE | MCU HIP4DP 350MHZ 360-PBGA |
| MPC755BVT350LE | MCU HIP4DP 350MHZ 360-PBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC8610VT800GZ | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MPC8610 Integrated Host Processor Hardware Specifications |
| MC8610VT800J | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications |
| MC861P | 制造商:Motorola Inc 功能描述: 制造商:Texas Instruments 功能描述: |
| MC862 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:INTEGRATED CIRCUITS |
| MC862L | 制造商:Motorola Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。