參數資料
型號： MC8610VT800GB
廠商： Freescale Semiconductor
文件頁數： 76/96頁
文件大?。?/td> 0K
描述： MPU E600 CORE 800MHZ 783-PBGA
標準包裝： 36
系列： MPC86xx
處理器類型： 32-位 MPC86xx PowerPC
速度： 800MHz
電壓： 1V
安裝類型： 表面貼裝
封裝/外殼： 783-BBGA，F(xiàn)CBGA
供應商設備封裝： 783-FCPBGA（29x29）
包裝： 托盤
MPC8610 Integrated Host Processor Hardware Specifications, Rev. 2
Hardware Design Considerations
Freescale Semiconductor
78
SerDes—Receiver lanes configured for PCI Express are allowed to be disconnected (as would occur when a PCI
Express slot is connected but not populated). Directions for terminating the SerDes signals is discussed in Section 3.10,
3.6
Pull-Up and Pull-Down Resistor Requirements
The MPC8610 requires weak pull-up resistors (2–10 k
Ω is recommended) on open drain type pins including I2C pins and PIC
interrupt pins.
Correct operation of the JTAG interface requires configuration of a group of system control pins as demonstrated in Figure 53.
Care must be taken to ensure that these pins are maintained at a valid deasserted state under normal operating conditions as most
have asynchronous behavior and spurious assertion will give unpredictable results.
Refer to the PCI 2.2 specification for all pull-ups required for PCI.
The following pins must not be pulled down during power-on reset: DIU_LD[5:6], MSRCID[1:2], HRESET_REQ, and
TRIG_OUT/READY.
The following are factory test pins and require strong pull up resistors (100
Ω – 1 kΩ) to OVDD: LSSD_MODE,
TEST_MODE[0:3].
The following pins require weak pull-up resistors (2–10 k
Ω) to their specific power supplies: LCS[0:4], LCS[5]/DMA_DREQ2,
LCS[6]/DMA_DACK[2], LCS[7]/DMA_DDONE[2], IRQ_OUT, IIC1_SDA, IIC1_SCL, IIC2_SDA, IIC2_SCL, and
CKSTP_OUT.
The following pins should be pulled to ground with a 100-
Ω resistor: SD1_IMP_CAL_TX, SD2_IMP_CAL_TX. The following
pins should be pulled to ground with a 200-
Ω resistor: SD1_IMP_CAL_RX, SD2_IMP_CAL_RX.
When the platform frequency is 400 MHz, cfg_platform_freq must be pulled down at reset. Also, cfg_dram_type[0 or 1] must
be valid at power-up even before HRESET assertion.
For other pin pull-up or pull-down recommendations of signals, see Section 1, “Pin Assignments and Reset States.”
3.7
Output Buffer DC Impedance
The MPC8610 drivers are characterized over process, voltage, and temperature. For all buses, the driver is a push-pull
single-ended driver type (open drain for I
2C).
To measure Z0 for the single-ended drivers, an external resistor is connected from the chip pad to OVDD or GND. Then, the
value of each resistor is varied until the pad voltage is OVDD/2 (see Figure 51). The output impedance is the average of two
components, the resistances of the pull-up and pull-down devices. When data is held high, SW1 is closed (SW2 is open) and
相關PDF資料
PDF描述
MPC8536CVTANGA MPU POWERQUICC III 783FCPBGA
MPC755CVT350LE MCU HIP4DP 350MHZ 360-PBGA
MPC755CRX350LE MCU HIP4DP 350MHZ 360-CBGA
MPC755CPX350LE MCU HIP4DP 350MHZ 360-PBGA
MPC755BVT350LE MCU HIP4DP 350MHZ 360-PBGA
相關代理商/技術參數
參數描述
MC8610VT800GZ 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MPC8610 Integrated Host Processor Hardware Specifications
MC8610VT800J 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
MC861P 制造商:Motorola Inc 功能描述: 制造商:Texas Instruments 功能描述:
MC862 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:INTEGRATED CIRCUITS
MC862L 制造商:Motorola Inc 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*