- 您現在的位置：買賣IC網 > PDF目錄45193 > MB91F345BPFT-GE1 32-BIT, FLASH, 50 MHz, RISC MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | MB91F345BPFT-GE1 |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, FLASH, 50 MHz, RISC MICROCONTROLLER, PQFP100 |
| 封裝： | 12 X 12 MM, 1.20 MM HEIGHT, 0.40 MM PITCH, PLASTIC, TQFP-100 |
| 文件頁數： | 9/72頁 |
| 文件大?。?/td> | 657K |
| 代理商： | MB91F345BPFT-GE1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
MB91345 Series
17
■ HANDLING DEVICES
Preventing Latch-up
Latch-up may occur in a COMS IC if a voltage greater than VCC pin, or less than VSS pin is applied to input
and output pins, or if an above-rating voltage is applied between VCC pin and VSS pin. If the latch-up occurs,
the significantly increases the power supply current and may cause thermal destruction of an element. Thus,
When you use a CMOS IC, be very careful not to exceed maximum voltage rating.
Treatment of Unused input pins
Do not leave an unused input pin open, since it may cause a malfunction. Thus, use pull-up or pull-down resistor.
About power supply pins
If there are multiple VCC pin or VSS pin, from the point of view of device design, pins to be of the same level
are connected the inside of the device to prevent such malfunctioning as latch-up. Be sure to connect all of them
to the power supply and ground externally for reducing unnecessary radiation, prevent malfunctioning of the
strobe signal due to the rise of ground level, and observe the total output current standard. In addition, consid-
eration should be given to connecting VCC/VSS of this device with as low an impedance as possible from the
current supply source. Also, we recommend connecting a ceramic capacitor of about 0.1 F as a bypass capacitor
between VCC and VSS near this device.
About crystal oscillator circuit
Noise near the X0 and X1 pins can cause this device to malfunction. Design the PC board such that X0 and X1
pins, crystal oscillator (or ceramic oscillator) , and bypass capacitor to the ground are placed as near one another
as possible. It is strongly recommended to design the PC board artwork with the X0/X1 pins surrounded by a
ground plane, as it expects stable operations.
Please ask the crystal maker to evaluate the oscillational characteristics of the crystal and this device.
About mode pins (MD0 to MD2)
These pins should be connected directly to VCC or VSS pins. To prevent the device erroneously switching to
test mode due to noise, design the PC board such that the distance between the mode pins and VCC or VSS
pins is as short as possible and the connection impedance is low.
About operation at power-on
Be sure to set initialized reset (INIT) with INIT pin immediately after power-on.
Immediately after turning on the power, be sure to continue connecting the Low level input to the INIT pin for
the stabilization wait time required for oscillator circuit, to secure the stabilization wait time of the oscillator and
regulator (For INIT via the INIT pin, the oscillation stabilization wait time setting is initialized to the minimum value) .
About oscillation input at power on
When turning on the power, be sure that clock input is maintained until the device is released from the oscillation
stabilization wait state.
Note on power-on/off sequences
When turning on the power, the output pin may be indeterminate until the internal power supply stabilizes.
相關PDF資料 |
PDF描述 |
|---|---|
| MB91F355APMT | 32-BIT, FLASH, 50 MHz, RISC MICROCONTROLLER, PQFP176 |
| MB91F365GB | 32-BIT, FLASH, 63.33 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F366GB | 32-BIT, FLASH, 63.33 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F368GBPMT | 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F366GBPMT | 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP120 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91F346B | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller CMOS FR60 Lite MB91345 Series |
| MB91F346BPFT-GE1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller CMOS FR60 Lite MB91345 Series |
| MB91F353A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F353APMCR-GE1 | 制造商:FUJITSU 功能描述: |
| MB91F353APMCR-G-JNE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。