參數資料
型號： MB91F267APMC-GE1
廠商： Fujitsu Semiconductor America Inc
文件頁數： 12/53頁
文件大小： 0K
描述： IC MCU FLASH 128KB FLASH 64LQFP
標準包裝： 1
系列： FR MB91265A
核心處理器： FR60Lite RISC
芯體尺寸： 32-位
速度： 33MHz
連通性： UART/USART
外圍設備： DMA，WDT
輸入/輸出數： 49
程序存儲器容量： 128KB（128K x 8）
程序存儲器類型： 閃存
RAM 容量： 4K x 8
電壓 - 電源 (Vcc/Vdd)： 4 V ~ 5.5 V
數據轉換器： A/D 11x8/10b
振蕩器型： 外部
工作溫度： -40°C ~ 105°C
封裝/外殼： 64-LQFP
包裝： 托盤
其它名稱： 865-1092
22
8183F–AVR–06/12
ATtiny24A/44A/84A
old value and program the new value) or to split the Erase and Write operations in two different
operations. The Programming times for the different modes are shown in Table 5-1.
When EEPE is set any write to EEPMn will be ignored. During reset, the EEPMn bits will be
reset to 0b00 unless the EEPROM is busy programming.
Bit 3 – EERIE: EEPROM Ready Interrupt Enable
Writing EERIE to one enables the EEPROM Ready Interrupt if the I-bit in SREG is set. Writing
EERIE to zero disables the interrupt. The EEPROM Ready Interrupt generates a constant inter-
rupt when Non-volatile memory is ready for programming.
Bit 2 – EEMPE: EEPROM Master Program Enable
The EEMPE bit determines whether writing EEPE to one will have effect or not.
When EEMPE is set, setting EEPE within four clock cycles will program the EEPROM at the
selected address. If EEMPE is zero, setting EEPE will have no effect. When EEMPE has been
written to one by software, hardware clears the bit to zero after four clock cycles.
Bit 1 – EEPE: EEPROM Program Enable
The EEPROM Program Enable Signal EEPE is the programming enable signal to the EEPROM.
When EEPE is written, the EEPROM will be programmed according to the EEPMn bits setting.
The EEMPE bit must be written to one before a logical one is written to EEPE, otherwise no
EEPROM write takes place. When the write access time has elapsed, the EEPE bit is cleared
by hardware. When EEPE has been set, the CPU is halted for two cycles before the next
instruction is executed.
Bit 0 – EERE: EEPROM Read Enable
The EEPROM Read Enable Signal – EERE – is the read strobe to the EEPROM. When the cor-
rect address is set up in the EEAR Register, the EERE bit must be written to one to trigger the
EEPROM read. The EEPROM read access takes one instruction, and the requested data is
available immediately. When the EEPROM is read, the CPU is halted for four cycles before the
next instruction is executed. The user should poll the EEPE bit before starting the read opera-
tion. If a write operation is in progress, it is neither possible to read the EEPROM, nor to change
the EEAR Register.
5.5.5
GPIOR2 – General Purpose I/O Register 2
Table 5-1.
EEPROM Programming Mode Bits and Programming Times
EEPM1
EEPM0
Programming Time
Operation
0
3.4 ms
Erase and Write in one operation (Atomic Operation)
0
1
1.8 ms
Erase Only
1
0
1.8 ms
Write Only
1
–
Reserved for future use
Bit
765
432
10
MSB
LSB
GPIOR2
Read/Write
R/W
Initial Value
0
相關PDF資料
PDF描述
ADUC7034BCPZ-RL IC MCU FLASH 32K ANLG IO 48LFCSP
ADUC7126BSTZ126IRL IC MCU 16/32B 126KB FLASH 80LQFP
AT91SAM7S256C-MU-999 IC MCU ARM7 256KB FLASH 64-VQFN
AT90USB1287-MUR MCU AVR 128K FLASH 16MHZ 64QFN
AT90USB1287-AUR MCU AVR 128K FLASH 16MHZ 64TQFP
相關代理商/技術參數
參數描述
MB91F267APMC-GS 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers
MB91F267APMC-GSE1 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers
MB91F267N 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontroller
MB91F267NA 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers
MB91F267NAPMC-G 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*