- 您現在的位置：買賣IC網 > PDF目錄102742 > MB91267NAPMC (FUJITSU LTD) 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | MB91267NAPMC |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP64 |
| 封裝： | 12 X 12 MM, 1.70 MM HEIGHT, 0.65 MM PITCH, PLASTIC, LFQFP-64 |
| 文件頁數： | 6/56頁 |
| 文件大小： | 473K |
| 代理商： | MB91267NAPMC |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
MB91265A Series
14
■ HANDLING DEVICES
Preventing Latch-up
Latch-up may occur in a CMOS IC if a voltage greater than VCC pin or less than VSS pin is applied to an input or
output pin or if an above-rating voltage is applied between VCC and VSS pins.
A latch-up, if it occurs, significantly increases the power supply current and may cause thermal destruction of
an element. When you use a CMOS IC, be very careful not to exceed the absolute maximum rating.
Treatment of Unused Input Pins
Do not leave an unused input pin open, since it may cause a malfunction. Handle by, for example, using a pull-
up or pull-down resistor.
About Power Supply Pins
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to external power supply
and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of strobe signals
caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1
F between VCC and VSS pins
near this device.
About Crystal Oscillator Circuit
Noise near the X0 and X1 pins may cause the device to malfunction. Design the printed circuit board so that X0
and X1 pins the crystal oscillator (or ceramic oscillator) , and the bypass capacitor to ground are located as
close to the device as possible.
It is strongly recommended to design the PC board artwork with the X0 and X1 pins surrounded by ground plane
because stable operation can be expected with such a layout.
Please ask the crystal maker to evaluate the oscillational characteristics of the crystal and this device.
About Mode Pins (MD0 to MD2)
These pins should be connected directly to VCC or VSS pins.
To prevent the device erroneously switching to test mode due to noise, design the printed circuit board such that
the distance between the mode pins and VCC or VSS pins is as short as possible and the connection impedance
is low.
Operation at Start-up
Be sure to execute setting initialized reset (INIT) with INIT pin immediately after start-up.
Also, in order to provide the oscillation stabilization wait time for the oscillation circuit immediately after start-up,
hold the “L” level input to the INIT pin for the required stabilization wait time (For INIT via the INIT pin, the
oscillation stabilization wait time setting is initialized to the minimum value) .
相關PDF資料 |
PDF描述 |
|---|---|
| M34280E1FP | 4-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDSO20 |
| MB90583CAPMC | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| M37161MA-XXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO42 |
| M3727GM6-XXXSP | 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP42 |
| M30823MW-XXXFP | 32-BIT, MROM, 30 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91270 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB912-952M02 | 制造商:SPC Multicomp 功能描述:TERMINAL BLOCK EUROSTYLE 2POS 24-10AWG 制造商:SPC Multicomp 功能描述:TERMINAL BLOCK EUROSTYLE, 2POS, 24-10AWG 制造商:SPC Multicomp 功能描述:TERMINAL BLOCK EUROSTYLE, 2POS, 24-10AWG; Connector Type:Eurostyle Terminal Block; Series:MB912; Connector Mounting:PCB; Pitch Spacing:9.52mm; Approvals / Standards:(Not Available); No. of Contacts:2; Contact Plating:Tin; Color:Green;RoHS Compliant: Yes |
| MB912-952M03 | 制造商:SPC Multicomp 功能描述:TERMINAL BLOCK EUROSTYLE 3POS 24-10AWG 制造商:SPC Multicomp 功能描述:TERMINAL BLOCK EUROSTYLE, 3POS, 24-10AWG 制造商:SPC Multicomp 功能描述:TERMINAL BLOCK EUROSTYLE, 3POS, 24-10AWG; Connector Type:Eurostyle Terminal Block; Series:MB912; Connector Mounting:PCB; Pitch Spacing:9.52mm; Approvals / Standards:(Not Available); No. of Contacts:3; Contact Plating:Tin; Color:Green;RoHS Compliant: Yes |
| MB91301 | 制造商:FUJI 制造商全稱:Fuji Electric 功能描述:32-Bit Proprietary Microcontroller |
| MB91302A | 制造商:FUJI 制造商全稱:Fuji Electric 功能描述:32-Bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。