- 您現在的位置：買賣IC網 > PDF目錄384713 > MAX9205 (Maxim Integrated Products, Inc.) Dual J-K Positive-Edge-Triggered Flip-Flops W/Clear And Preset 16-CFP -55 to 125 PDF資料下載
參數資料
| 型號： | MAX9205 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Dual J-K Positive-Edge-Triggered Flip-Flops W/Clear And Preset 16-CFP -55 to 125 |
| 中文描述： | 10位、總線式LVDS串行器 |
| 文件頁數： | 6/13頁 |
| 文件大?。?/td> | 180K |
| 代理商： | MAX9205 |
M
Initialization Mode
When V
CC
is applied, the outputs are held in high
impedance and internal circuitry is disabled by on-chip
power-on-reset circuitry. When V
CC
reaches 2.35V, the
PLL starts to lock to a local reference clock (16MHz to
40MHz for MAX9205 and 40MHz to 66MHz for
MAX9207). The reference clock, TCLK, is provided by
the system. A serializer locks within 2049 cycles of
TCLK. Once locked, a serializer is ready to send data
or SYNC patterns depending on the levels of SYNC 1
and SYNC 2.
Synchronization Mode
To rapidly synchronize with a deserializer, SYNC pat-
terns can be sent. A SYNC pattern is six consecutive
ones followed by six consecutive zeros repeating every
TCLK period. When one or both SYNC inputs are
asserted high for at least six cycles of TCLK, the serial-
izer will initiate the transmission of 1024 SYNC patterns.
The serializer will continue to send SYNC patterns if
either of the SYNC input pins remains high. Toggling
one SYNC input with the other SYNC input low before
1024 SYNC patterns are output does not interrupt the
output of the 1024 SYNC patterns.
Data Transmission Mode
After initialization, both SYNC input pins must be set
low by users or through a control signal from the dese-
rializer before data transmission begins. Provided that
SYNC inputs are low, input data at IN0
–
9 are clocked
into the serializer by the TCLK input. Setting TCLK_R/
F
high selects the rising edge of TCLK for data strobe
and low selects the falling edge. If either of the SYNC
inputs goes high for six TCLK cycles at any time during
data transmission, the data at IN0
–
9 are ignored and
SYNC patterns are sent for at least 1024 TCLK cycles.
A start bit high and a stop bit low frame the 10-bit data
and function as the embedded clock edge in the serial
data stream. The serial rate is the TCLK frequency
times the data and appended bits. For example, if
TCLK is 40MHz, the serial rate is 40 x 12 (10 + 2 bits) =
480Mbps. Since only 10 bits are from input data, the
payload rate is 40 x 10 = 400Mbps.
Power-Down
Power-down mode is entered when the
PWRDN
pin is
driven low. In power-down mode, the PLL of the serial-
izer is stopped and the outputs (OUT+ and OUT-) are
in high impedance, disabling drive current and also
reducing supply current. When
PWRDN
is driven high,
the serializer must reinitialize and resynchronize before
data can be transferred.
High-Impedance State
The serializer output pins (OUT+ and OUT-) are held in
high impedance when V
CC
is first applied and while the
PLL is locking to the local reference clock. Setting EN
or
PWRDN
low puts the device in high impedance.
After initialization, EN functions asynchronously. For
example, the serializer output can be put into high
impedance while SYNC patterns are being sent without
affecting the internal timing of the SYNC pattern gener-
ation. However, if the serializer goes into high imped-
ance, a deserializer loses PLL lock and needs to
resynchronize before data transfer can resume.
10-Bit Bus LVDS Serializers
6
_______________________________________________________________________________________
Table 1. Input /Output Function Table
INPUTS
OUTPUTS
EN
PWRDN
SYNC 1
SYNC 2
OUT+, OUT-
H
H
When either or both SYNC 1
and SYNC 2 are held high for
at least six TCLK cycles
Synchronization Mode. SYNC patterns of six 1s and six 0s are
transmitted every TCLK cycle for at least 1024 TCLK cycles.
Data at IN0
–
9 are ignored.
H
H
L
L
Data Transmission Mode. IN0
–
9 and 2 frame bits are
transmitted every TCLK cycle.
X
L
X
X
L
X
X
X
Output in high-impedance.
X = Don
’
t care
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9205EAI | Dual J-K Positive-Edge-Triggered Flip-Flops W/Clear And Preset 20-LCCC -55 to 125 |
| MAX9321B | Hex Inverters 14-CDIP -55 to 125 |
| MAX9321BESA | Hex Inverters 14-CFP -55 to 125 |
| MAX9394-MAX9395 | CB 2C 2#16S PIN RECP BOX |
| MAX9394 | 2:1 Multiplexers and 1:2 Demultiplexers with Loopback |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9205_10 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:10-Bit Bus LVDS Serializers |
| MAX9205EAI | 功能描述:LVDS 接口集成電路 RoHS:否 制造商:Texas Instruments 激勵器數量:4 接收機數量:4 數據速率:155.5 Mbps 工作電源電壓:5 V 最大功率耗散:1025 mW 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-16 Narrow 封裝:Reel |
| MAX9205EAI/V+ | 功能描述:串行器/解串器 - Serdes 10-Bit Bus LVDS Serializer RoHS:否 制造商:Texas Instruments 類型:Deserializer 數據速率:1.485 Gbit/s 輸入類型:ECL/LVDS 輸出類型:LVCMOS 輸入端數量:1 輸出端數量:20 工作電源電壓:2.375 V to 2.625 V 工作溫度范圍:0 C to + 70 C 封裝 / 箱體:TQFP-64 |
| MAX9205EAI/V+T | 功能描述:串行器/解串器 - Serdes 10-Bit Bus LVDS Serializer RoHS:否 制造商:Texas Instruments 類型:Deserializer 數據速率:1.485 Gbit/s 輸入類型:ECL/LVDS 輸出類型:LVCMOS 輸入端數量:1 輸出端數量:20 工作電源電壓:2.375 V to 2.625 V 工作溫度范圍:0 C to + 70 C 封裝 / 箱體:TQFP-64 |
| MAX9205EAI+ | 功能描述:串行器/解串器 - Serdes 10-Bit Bus LVDS Serializer RoHS:否 制造商:Texas Instruments 類型:Deserializer 數據速率:1.485 Gbit/s 輸入類型:ECL/LVDS 輸出類型:LVCMOS 輸入端數量:1 輸出端數量:20 工作電源電壓:2.375 V to 2.625 V 工作溫度范圍:0 C to + 70 C 封裝 / 箱體:TQFP-64 |
發布緊急采購，3分鐘左右您將得到回復。