- 您現在的位置：買賣IC網 > PDF目錄1938 > MAX3109ETJ+ (Maxim Integrated Products)SEMICONDUCTOR OTHER PDF資料下載
參數資料
| 型號： | MAX3109ETJ+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 50/66頁 |
| 文件大小： | 0K |
| 描述： | SEMICONDUCTOR OTHER |
| 標準包裝： | 60 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
Dual Serial UART with 128-Word FIFOs
MAX3109
54
Maxim Integrated
Transmitter Synchronization Register (TxSynch)
The TxSynch register is used to configure transmitter synchronization with a global SPI or I2C command. One of 16
trigger commands (Table 5) can be selected to be the synchronization trigger source individually for each UART. This
allows simultaneous start of transmission of multiple UARTs that are associated with the same global trigger command.
The synchronized UARTs can be on either a single MAX3109 or multiple devices if they are controlled by a common
SPI interface.
The UARTs start transmission when a global trigger command is received. Start of transmission is considered to be
the falling edge of the START bit at the TX_ output. A delay can optionally be programmed through the SynchDelay1
and SynchDelay2 registers.
TX synchronization is managed through software by transmitting the broadcast trigger Tx command (Table 5) to the
MAX3109 through the SPI or I2C interface. To selectively synchronize ports that are on the same MAX3109 (intrachip
synchronization) or on different MAX3109 (interchip synchronization) devices, up to 16 trigger Tx commands have
been defined (see the Global Command Register (GloblComnd) section for more information).
Bit 7: CLKtoGPIO
The CLKtoGPIO bit is used to provide a buffered replica of the UARTs system clock (i.e., the fractional baud-rate gen-
erator input) to a GPIO. UART0’s clock is routed to GPIO0 and UART1’s clock is routed to GPIO4.
Bit 6: TxAutoDis
Set the TxAutoDis bit high to enable automatic transmitter disabling. When TxAutoDis is set high, the transmitter is
automatically disabled when all data in the TxFIFO has been transmitted. After the transmitter is disabled, the TxFIFO
can then be filled with data that will be transmitted when its assigned trigger command is received, as defined by the
TrigSelx bits.
Bit 5: TrigDelay
Set the TrigDelay bit high to enable delayed start of transmission when a trigger command is received. The UART
starts transmitting data following a delay programmed in SynchDelay1 and SynchDelay2 after receiving the assigned
trigger command.
Bit 4: SynchEn
Set the SynchEn bit high to enable software TX synchronization mode. If SynchEn is set high, the UART starts transmit-
ting data when the assigned trigger command is received and the TxFIFO contains data. Setting SynchEn high forces
the MODE1[1]: TxDisabl bit high and thereby disables the UART’s transmitter. This prevents the transmitter from send-
ing data as soon as the TxFIFO is loaded. Once the TxFIFO has been loaded, the UART starts transmitting data only
upon receiving the assigned trigger command.
Set the SynchEn bit low to disable transmitter synchronization for that UART. If SynchEn is set low, that UART’s trans-
mitter does not start transmission through any trigger command.
Bits 3–0: TrigSelx
The TrigSelx bits assign the trigger command for that UART’s transmitter synchronization when SynchEn is set high.
For example, set TxSynch[3:0] to 0x08 for the UART to be triggered by TX command 8 (0xE8, Table 5).
ADDRESS:
0x20
MODE:
R/W
BIT
7
6
5
4
3
2
1
0
NAME
CLKtoGPIO
TxAutoDis
TrigDelay
SynchEn
TrigSel3
TrigSel2
TrigSel1
TrigSel0
RESET
0
相關PDF資料 |
PDF描述 |
|---|---|
| MAX310CPE | IC VIDEO MULTIPLEXER 8X1 16DIP |
| MAX3110EENI+G36 | IC UART SPI COMPAT 28-DIP |
| MAX3120CUA+ | IC TXRX INFRARED IRDA 8-UMAX |
| MAX3120EUA | IC TXRX 3V IRDA IR 3V 8-UMAX |
| MAX312ESE | IC SWITCH QUAD SPST 16SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3109ETJ+ | 功能描述:UART 接口集成電路 Dual Serial UART with 128-Word FIFOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| MAX3109ETJ+T | 功能描述:UART 接口集成電路 Dual Serial UART with 128-Word FIFOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| MAX310C/D | 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MAX310CPE | 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MAX310CPE+ | 功能描述:多路器開關 IC 8:1 Unbuffered RF Video MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。