- 您現在的位置：買賣IC網 > PDF目錄383334 > MAX1977EEI (MAXIM INTEGRATED PRODUCTS INC) High-Efficiency, Quad Output, Main Power- Supply Controllers for Notebook Computers PDF資料下載
參數資料
| 型號： | MAX1977EEI |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | High-Efficiency, Quad Output, Main Power- Supply Controllers for Notebook Computers |
| 中文描述： | DUAL SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | 0.150 INCH, 0.025 INCH PITCH, QSOP-28 |
| 文件頁數： | 12/32頁 |
| 文件大?。?/td> | 497K |
| 代理商： | MAX1977EEI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
M
High-Effic ienc y, Quad Output, Main Power-
S upply Controllers for Notebook Computers
12
______________________________________________________________________________________
Pin Desc ription
PIN
MAX1777
MAX1977
MAX1999
NAME
FUNCTION
1
—
CS3
3.3V SMPS Current-Sense Input. Connect CS3 to a current-sensing resistor from the source of
the synchronous rectifier to GND. The voltage at ILIM3 determines the current-limit threshold
(see the
Current-Limit (ILIM) Circuit
section).
No Connection. Not internally connected.
Power-Good Output. PGOOD is an open-drain output that is pulled low if either output is
disabled or is more than 10% below its nominal value.
3.3V SMPS Enable Input. The 3.3V SMPS is enabled if ON3 is greater than the SMPS on level
and disabled if ON3 is less than the SMPS off level. If ON3 is connected to REF, the 3.3V
SMPS starts after the 5V SMPS reaches regulation (delay start). Drive ON3 below the clear
fault level to reset the fault latches.
5V SMPS Enable Input. The 5V SMPS is enabled if ON5 is greater than the SMPS on level and
disabled if ON5 is less than the SMPS off level. If ON5 is connected to REF, the 5V SMPS
starts after the 3.3V SMPS reaches regulation (delay start). Drive ON5 below the clear fault
level to reset the fault latches.
3.3V SMPS Current-Limit Adjustment. The GND-LX current-limit threshold defaults to 100mV if
ILIM3 is tied to V
CC
. In adjustable mode, the current-limit threshold is 1/10th the voltage seen
at ILIM3 over a 0.5V to 3V range. The logic threshold for switchover to the 100mV default value
is approximately V
CC
- 1V. Connect ILIM3 to REF for a fixed 200mV threshold.
Shutdown Control Input. The device enters its 6μA supply current shutdown mode if
V
SHDN
is less than the
SHDN
input falling edge trip level and does not restart until V
SHDN
is
greater than the
SHDN
input rising edge trip level. Connect
SHDN
to V+ for automatic startup.
SHDN
can be connected to V+ through a resistive voltage-divider to implement a
programmable undervoltage lockout.
3.3V SMPS Feedback Input. Connect FB3 to GND for fixed 3.3V operation. Connect FB3 to a
resistive voltage-divider from OUT3 to GND to adjust the output from 2V to 5.5V.
2V Reference Output. Bypass to GND with a 0.22μF (min) capacitor. REF can source up to
100μA for external loads. Loading REF degrades FB_ and output accuracy according to the
REF load-regulation error.
5V SMPS Feedback Input. Connect FB5 to GND for fixed 5V operation. Connect FB5 to a
resistive voltage-divider from OUT5 to GND to adjust the output from 2V to 5.5V.
Overvoltage and Undervoltage Fault Protection Enable/Disable. Connect
PRO
to V
CC
to
disable undervoltage and overvoltage protection. Connect
PRO
to GND to enable
undervoltage and overvoltage protection (see the
Fault Protection
section).
5V SMPS Current-Limit Adjustment. The GND-LX current-limit threshold defaults to 100mV if
ILIM5 is tied to V
CC
. In adjustable mode, the current-limit threshold is 1/10th the voltage seen
at ILIM5 over a 0.5V to 3V range. The logic threshold for switchover to the 100mV default value
is approximately V
CC
- 1V. Connect ILIM5 to REF for a fixed 200mV threshold.
Low-Noise Mode Control. Connect
SKIP
to GND for normal idle-mode (pulse-skipping)
operation or to V
CC
for PWM mode (fixed frequency). Connect to REF or leave floating for
ultrasonic mode (pulse skipping, 25kHz minimum).
—
1
N.C.
2
2
PGOOD
3
3
ON3
4
4
ON5
5
5
ILIM3
6
6
SHDN
7
7
FB3
8
8
REF
9
9
FB5
10
10
PRO
11
11
ILIM5
12
12
SKIP
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1999EEI | High-Efficiency, Quad Output, Main Power- Supply Controllers for Notebook Computers |
| MAX1778 | 32-Bit Digital Signal Controller with ROM 100-LQFP -40 to 85 |
| MAX1880 | Quad-Output TFT LCD DC-DC Converters with Buffer |
| MAX1881 | Quad-Output TFT LCD DC-DC Converters with Buffer |
| MAX1882 | Quad-Output TFT LCD DC-DC Converters with Buffer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1977EEI+ | 功能描述:DC/DC 開關控制器 Quad Out Main Power Supply Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1977EEI+T | 功能描述:DC/DC 開關控制器 Quad Out Main Power Supply Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1977EEI-T | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1977EEI-TG068 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1978ETM | 功能描述:電壓模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。