- 您現在的位置：買賣IC網 > PDF目錄383342 > MAX195BMDE (MAXIM INTEGRATED PRODUCTS INC) 16-Bit, 85ksps ADC with 10レA Shutdown PDF資料下載
參數資料
| 型號： | MAX195BMDE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | 16-Bit, 85ksps ADC with 10レA Shutdown |
| 中文描述： | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, CDIP16 |
| 封裝： | 0.300 INCH, SIDEBRAZED, CERAMIC, DIP-16 |
| 文件頁數： | 15/28頁 |
| 文件大?。?/td> | 311K |
| 代理商： | MAX195BMDE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Digital Noise
Digital noise can easily be coupled to AIN and REF. The
conversion clock (CLK) and other digital signals that are
active during input acquisition contribute noise to the con-
version result. If the noise signal is synchronous to the
sampling interval, an effective input offset is produced.
Asynchronous signals produce random noise on the input,
whose high-frequency components may be aliased into
the frequency band of interest. Minimize noise by present-
ing a low impedance (at the frequencies contained in the
noise signal) at the inputs. This requires bypassing AIN to
AGND, or buffering the input with an amplifier that has a
small-signal bandwidth of several megahertz, or prefer-
ably both. AIN has a bandwidth of about 16MHz.
Offsets resulting from synchronous noise (such as the
conversion clock) are canceled by the MAX195’s cali-
bration scheme. However, because the magnitude of
the offset produced by a synchronous signal depends
on the signal’s shape, recalibration may be appropriate
if the shape or relative timing of the clock or other digi-
tal signals change, as might occur if more than one
clock signal or frequency is used.
Distortion
Avoid degrading dynamic performance by choosing an
amplifier with distortion much less than the MAX195’s
THD (-97dB, or 0.0014%) at frequencies of interest. If
the chosen amplifier has insufficient common-mode
rejection, which results in degraded THD performance,
use the inverting configuration (positive input ground-
ed) to eliminate errors from this source. Low tempera-
ture-coefficient, gain-setting resistors reduce linearity
errors caused by resistance changes due to self-heat-
ing. Also, to reduce linearity errors due to finite amplifier
gain, use an amplifier circuit with sufficient loop gain at
the frequencies of interest (Figures 14, 15, 16).
DC Accuracy
If DC accuracy is important, choose a buffer with an
offset much less than the MAX195’s maximum offset
(±3LSB = ±366μV for a ±4V input range), or whose
offset can be trimmed while maintaining good stability
over the required temperature range.
Recommended Circuits
Figure 14 shows a good circuit for DC and low-frequen-
cy use. The MAX400 has very low offset (10μV) and
drift (0.2μV/°C), and low voltage noise (10nV/
√
Hz
) as
well. However, its gain-bandwidth product (GBW) is
much too low to drive AIN directly, so the analog input
is bypassed to present a low impedance at high fre-
quencies. The large bypass capacitor is isolated from
the amplifier output by a 100
resistor, which provides
additional noise filtering. Since the ±15V supplies
exceed the AIN range, add protection diodes at AIN
(see REF and AIN Input Protection section).
Figure 15 shows a wide-bandwidth amplifier (MAX427)
driving a wideband video buffer, which is capable of
driving AIN and a small bypass capacitor (for noise
reduction) directly. The video buffer is inside the
MAX427’s feedback loop, providing good DC accura-
cy, while the buffer’s low output impedance and high-
current capability provide good AC performance. AIN is
diode-clamped to the ±5V rails to prevent overvoltage.
The MAX427’s 15μV maximum offset voltage, 0.8μV/°C
maximum drift, and less than 5nV/
√
Hz
noise specifica-
tions make this an excellent choice for AC/DC use.
M
16-Bit, 85ksps ADC with 10μA S hutdown
______________________________________________________________________________________
15
MAX427
4
7
6
2
2
3
IN
+15V
-15V
0.0033
μ
F
0.1
μ
F
0.1
μ
F
ELANTEC
EL2003
4
1
7
+15V
-15V
0.1
μ
F
0.1
μ
F
100pF
1k
1k
1N914
1N914
+5V
-5V
AIN
10
Figure 15. AIN Buffer for AC/DC Use
相關PDF資料 |
PDF描述 |
|---|---|
| MAX196-MAX198 | Multirange, Single %V, 12-Bit DAS with 12-Bit Bus Interface |
| MAX196AMYI | Circular Connector; No. of Contacts:18; Series:MS27505; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:15; Circular Contact Gender:Pin; Circular Shell Style:Box Mount Receptacle; Insert Arrangement:15-18 RoHS Compliant: No |
| MAX198AMYI | Circular Connector; No. of Contacts:18; Series:MS27505; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:15; Circular Contact Gender:Socket; Circular Shell Style:Box Mount Receptacle RoHS Compliant: No |
| MAX198AEAI | Multirange, Single %V, 12-Bit DAS with 12-Bit Bus Interface |
| MAX198BENI | Multirange, Single %V, 12-Bit DAS with 12-Bit Bus Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX195EVC16-DIP | 功能描述:模數轉換器 - ADC Programmers, Development Systems RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX195EVKIT-DIP | 功能描述:數據轉換 IC 開發工具 Programmers, Development Systems RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX1960EEP | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1960EEP+ | 功能描述:DC/DC 開關控制器 1MHz PWM Step-Down RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1960EEP+T | 功能描述:DC/DC 開關控制器 1MHz PWM Step-Down RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。