參數資料
型號： MAX16049ATN+
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： 電源管理
英文描述： 8-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC56
封裝： 8 X 8 MM, ROHS COMPLIANT, TQFN-56
文件頁數： 32/61頁
文件大?。?/td> 790K
代理商： MAX16049ATN+
MAX16047A/MAX16049A
12-Channel/8-Channel EEPROM-Programmable
System Managers with Nonvolatile Fault Registers
38
______________________________________________________________________________________
Power-Up/Power-Down Faults
All EN_OUTs are deasserted if an overvoltage or under-
voltage fault is detected during power-up/power-down
(regardless of the critical fault enable bits). Under these
conditions, information of the failing slot is stored in
EEPROM r00h[3:0] unless the fault register is config-
ured not to store any information by setting r47h[1:0] to
‘11’ (see Table 17).
If there is a tracking fault on a channel configured for
closed-loop tracking, a fault log operation occurs and the
bits representing the failed tracking channels are set to
‘0’ unless the fault register is configured not to store any
information by setting r47h[1:0] to ‘11’ (see Table 17).
Autoretry/Latch Mode
For critical faults, the MAX16047A/MAX16049A can be
configured for one of two fault management methods:
autoretry or latch-on-fault. Set r4Fh[3] to ‘0’ to select
autoretry mode. In this configuration, the device will
shut down after a critical fault event and then restart fol-
lowing a configurable delay. Use r4Fh[2:0] to select an
autoretry delay from 20s to 2.4s. See Table 19 for
more information on setting the autoretry delay.
Set r4Fh[3] to ‘1’ to select the latch-on-fault mode. In
this configuration EN_OUT_s are deasserted after a
critical fault event. The device does not re-initiate the
power-up sequence until EN is toggled or the Software
Enable bit is reset to ‘0.’ See the Enable section for
more information on setting the Software Enable bit.
If fault information is stored in EEPROM (see the
Critical
Faults section) and autoretry mode is selected, set an
autoretry delay greater than the time required for the
storing operation. If fault information is stored in EEP-
ROM and latch-on-fault mode is chosen, toggle EN or
reset the Software Enable bit only after the completion
of the storing operation. If saving information about the
failed lines only, ensure a delay of at least 90ms before
the restart procedure. Otherwise, ensure a minimum
306ms timeout. This ensures that ADC conversions are
completed and values are stored correctly in EEPROM.
See Table 20 for more information about required fault
log operation periods.
Table 19. Fault Recovery Configuration
REGISTER/
EEPROM
ADDRESS
BIT RANGE
DESCRIPTION
[2:0]
Autoretry Delay
000 = 20s
001 = 18.75ms
010 = 37.5ms
011 = 75ms
100 = 150ms
101 = 300ms
110 = 600ms
111 = 2.4s
[3]
Fault Recovery Mode
0 = Autoretry procedure is performed following a fault event
1 = Latchoff on fault
[5:4]
Slew Rate
00 = 800V/s
01 = 400V/s
10 = 200V/s
11 = 100V/s
4Fh
[7:6]
Fault Deglitch
00 = 2 conversions
01 = 4 conversions
10 = 8 conversions
11 = 16 conversions
相關PDF資料
PDF描述
MAX2042AETP+T TELECOM, CELLULAR, RF AND BASEBAND CIRCUIT, QCC20
MAX2042AETP+ TELECOM, CELLULAR, RF AND BASEBAND CIRCUIT, QCC20
MAX2102CWI Direct-Conversion Tuner ICs for Digital DBS Applications
MAX3202EEBT-T UNIDIRECTIONAL, 4 ELEMENT, SILICON, TVS DIODE
MAX359MJE Fault-Protected Analog Multiplexer
相關代理商/技術參數
參數描述
MAX16049ATN+ 功能描述:監控電路 8Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX16049ATN+T 功能描述:監控電路 8Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX16049ETN+ 功能描述:監控電路 8Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX16049ETN+T 功能描述:監控電路 8Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX1604EAI 功能描述:電源開關 IC - 配電 RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*