- 您現在的位置：買賣IC網 > PDF目錄9499 > MAX1407CAI+ (Maxim Integrated Products)IC DAS 16BIT LP 28-SSOP PDF資料下載
參數資料
| 型號： | MAX1407CAI+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 19/48頁 |
| 文件大小： | 0K |
| 描述： | IC DAS 16BIT LP 28-SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 46 |
| 類型： | 數據采集系統（DAS） |
| 分辨率（位）： | 16 b |
| 采樣率（每秒）： | 60 |
| 數據接口： | 串行 |
| 電壓電源： | 模擬和數字 |
| 電源電壓： | 2.7 V ~ 3.6 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 28-SSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
MAX1407/MAX1408/MAX1409/MAX1414
Low-Power, 16-Bit Multichannel DAS with
Internal Reference,10-Bit DACs, and RTC
26
______________________________________________________________________________________
MODE: Conversion Mode bit. A logic zero selects a
normal ADC conversion, while a logic 1 selects an offset
calibration conversion. After completing a calibration
conversion, MODE automatically resets to zero.
RATE: Conversion Rate bit. A logic zero selects a 30Hz
conversion rate while a logic 1 selects a 60Hz conver-
sion rate.
GAIN1, GAIN0: Gain bits. The Gain bits select the PGA
gain. For an ADC gain of +1/3, +1, and 2V/V, [GAIN1
GAIN0] are 00, 01, and 10, respectively.
BUFP: Positive Buffer bit. When this bit is 0, the positive
input buffer is bypassed and powered down. When this
bit is 1 and the BUFE bit in the Power1 register is 1, the
positive input buffer drives the ADC input sampling
capacitors.
BUFN: Negative Buffer bit. When this bit is 0, the nega-
tive input buffer is bypassed and powered-down. When
this bit is 1 and the BUFE bit in the Power1 register is 1,
the negative input buffer drives the ADC input sampling
capacitors.
BIP: Unipolar/Bipolar bit. A logic zero selects unipolar
mode while a logic 1 selects bipolar mode.
STA1: Start bit. Setting STA1 to a logic 1 resets the reg-
isters inside the ADC filter, updates the ADC configura-
tion according to the ADC register, and initiates an
analog-to-digital conversion or offset calibration. The
initial conversion requires three cycles for valid output
data, and each subsequent conversion cycle will output
valid data. After completing the intial conversion, STA1
automatically resets to 0; however, the ADC will contin-
ue to do conversions until it is powered down.
Writing to the ADC register with STA1 set to 0 updates
the ADC register without changing the ADC configura-
tion and allows the ADC to continue conversions unin-
terrupted. This allows the ADC and MUX configuration
to be updated simultaneously. See STA2 bit of the MUX
register.
ADC REGISTER (00000)
FIRST BIT (MSB)
(LSB)
NAME
MODE
RATE
GAIN1
GAIN0
BUFP
BUFN
BIP
STA1
DEFAULTS
0000
On-Chip Registers
MUXP2, MUXP1, MUXP0: Positive Multiplexer bits.
MUXP[2:0] direct one-of-eight positive inputs to the
positive input of the ADC. Table 4 relates the MUXP bits
to the positive multiplexer inputs.
MUXN2, MUXN1, MUXN0: Negative Multiplexer bits.
MUXN[2:0] direct one-of-eight (one-of-four for the
MAX1409) negative inputs to the negative input of the
ADC. Table 5 relates the MUXN bits to the negative
multiplexer inputs.
DBIT: Digital Output bit. This bit controls the output
state of D0. When the output buffer is enabled, D0 is
low if Dbit is equal to 0, and high if Dbit is equal to 1.
D0 is enabled by the D0E bit of the Power2 register.
STA2: Start bit. Setting STA2 to a logic 1 updates the
mux selection, resets the registers inside the ADC filter,
updates the ADC configuration according to the ADC
register, and initiates an analog-to-digital conversion.
The initial conversion requires three cycles for valid out-
put data, and each subsequent conversion cycle will
output valid data. STA2 automatically resets to 0 after
the initial conversion completes. The ADC will continue
to do conversions until it is powered down. Writing to
the MUX register with the STA2 bit set to 0, updates the
MUX register and selection, but leaves the ADC config-
uration unchanged. The MUX input can be switched
with the ADC continuously converting without the digital
filter resetting.
MUX REGISTER (00001)
FIRST BIT (MSB)
(LSB)
NAME
MUXP2
MUXP1
MUXP0
MUXN2
MUXN1
MUXN0
DBIT
STA2
DEFAULTS
0000
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1414CAI+ | IC DAS 16BIT LP 28-SSOP |
| NBXDPA019LN1TAG | IC CLK XO LVDS 125/250MHZ 6CLCC |
| MAX181CCQH+D | IC DAS 12BIT 100KSPS 44-PLCC |
| 74AC138SC | IC DECODER/DEMUX 1OF8 16-SOIC |
| MAX181CCQH-D | IC DAS 6CH 12BIT 100KHZ 44-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1407CAI+ | 功能描述:ADC / DAC多通道 16-Bit 4Ch 60sps 1.35V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1407CAI+T | 功能描述:ADC / DAC多通道 16-Bit 4Ch 60sps 1.35V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1407CAI-T | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1407EAI+ | 制造商:Maxim Integrated Products 功能描述:LOW-POWER 16-BIT MULTICHANNEL DAS - Rail/Tube |
| MAX1407EAI+T | 制造商:Maxim Integrated Products 功能描述:LOW-POWER 16-BIT MULTICHANNEL DAS - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。