- 您現在的位置：買賣IC網 > PDF目錄370849 > M37754M8C-XXXHP (Mitsubishi Electric Corporation) SINGLE-CHIP 16BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M37754M8C-XXXHP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 16BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片16位微機的CMOS |
| 文件頁數： | 59/114頁 |
| 文件大?。?/td> | 1116K |
| 代理商： | M37754M8C-XXXHP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁
59
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
MITSUBISHI MICROCOMPUTERS
M37754M8C-XXXGP, M37754M8C-XXXHP
M37754S4CGP, M37754S4CHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
(2) Repeat mode
Repeat mode is selected when bit 3 of A-D control register 0 is “1”,
bit 4 is “0” and bit 2 of A-D control register 1 is “0”.
The operation of this mode is the same as the operation of one-shot
mode except that when A-D conversion of the selected pin is com-
plete and the result is stored in the A-D register, conversion does not
stop, but is repeated.
No interrupt request is generated in this mode. Furthermore, if soft-
ware trigger is selected, the A-D conversion start bit is not cleared.
The contents of the A-D register can be read at any time.
Be sure not to write to the A-D register corresponding to the pins se-
lected for a comparator during operation.
(3) Single sweep mode
Single sweep mode is selected when bit 3 of A-D control register 0
is “0”, bit 4 is “1” and bit 2 of A-D control register 1 is “0”.
In the single sweep mode, the number of analog input pins to be
swept can be selected. Analog input pins are selected by bits 1 and
0 of the A-D control register 1 (address 1F
16
). Two pins, four pins,
six pins, or eight pins can be selected as analog input pins, depend-
ing on the contents of these bits.
A-D conversion is performed only for selected input pins. After A-D
conversion is performed for input of AN
0
pin, the conversion result
is stored in A-D register 0, and in the same way, A-D conversion is
performed for selected pins one after another. After A-D conversion
is performed for all selected pins, the sweep is stopped.
A-D conversion can be started with a software trigger or with an ex-
ternal trigger input. A software trigger is selected when bit 5 is “0”
and an external trigger is selected when it is “1”.
When a software trigger is selected, A-D conversion is started when
A-D control register 0 bit 6 (A-D conversion start bit) is set to “1.”
When A-D conversion of all selected pins end, the interrupt request
bit of the A-D conversion interrupt control register is set to “1.” At the
same time, A-D conversion start bit is cleared to “0” and A-D conver-
sion stops.
When an external trigger is selected, A-D conversion starts when
the A-D conversion start bit is “1” and the AD
TRG
input changes from
“H” to “L”. In this case, the A-D conversion result which is stored in
the A-D register 7 becomes invalid because the AD
TRG
pin is multi-
plexed with AN
7
pin.
The operation by external trigger is the same as that by software
trigger except that the A-D conversion start bit is not cleared to “0”
after A-D conversion and a retrigger can be available during A-D
conversion.
(4) Repeat sweep mode 0
Repeat sweep mode 0 is selected when bit 3 of A-D control register
0 is “1”, bit 4 is “1” and bit 2 of A-D control register 1 is “0”.
The difference from the single sweep mode is that A-D conversion
does not stop after conversion for all selected pins, but repeats
again from the AN
0
pin. The repeat is performed among the selected
pins. Also, no interrupt request is generated. Furthermore, if soft-
ware trigger is selected, the A-D convension start bit is not cleared.
The A-D register can be read at any time.
Be sure not to write to the A-D register corresponding to the pins se-
lected for a comparator during operation.
(5) Repeat sweep mode 1
Repeat sweep mode 1 is selected when bit 3 of A-D control register
0 is “1”, bit 4 is “1” and bit 2 of A-D control register 1 is “1”.
The difference from the repeat sweep mode 0 is that A-D conversion
for one unselected pin is performed each time when A-D conversion
for selected pins is completed and A-D conversion is repeated once
again from AN
0
pin. The number of analog input pins to be swept is
also different.
The analog input pins for repeatedly sweep are selected with bits 1
and 0 of A-D control register 1. The contents of these pins are used
to select one pin, two pins, three pins, or four pins.
The unselected pins are converted from the pin next to the pins se-
lected as repeat sweep pins. No interrupt request is generated. Fur-
thermore, if software trigger is selected, the A-D conversion start bit
is not cleared.
The A-D register can be read at any time.
Be sure not to write to the A-D register corresponding to the pins se-
lected for a comparator during operation.
Note:
Clear the interrupt request bit of the A-D interrupt control reg-
ister (bit 3 at address 70
16
) before using the A-D interrupt. It is
because the interrupt request bit is undefined just after reset.
相關PDF資料 |
PDF描述 |
|---|---|
| M37754S4CGP | SINGLE-CHIP 16BIT CMOS MICROCOMPUTER |
| M37754S4CHP | SINGLE-CHIP 16BIT CMOS MICROCOMPUTER |
| M37754 | SINGLE-CHIP 16BIT CMOS MICROCOMPUTER |
| M37754M8C | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37902F8CHP | DIODE SCHOTTKY DUAL COMMON-ANODE 25V 200mW 0.32V-vf 200mA-IFM 1mA-IF 2uA-IR SOT-23 3K/REEL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37754S4CGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16BIT CMOS MICROCOMPUTER |
| M37754S4CHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M3775PR-H400CL | 制造商:Bonitron 功能描述:OVERVOLTAGE BRAKING RESISTOR |
| M3775RK-0.75A | 制造商:Bonitron 功能描述:OVERVOLTAGE BRAKING RESISTOR |
| M3775RK-C0.50A | 制造商:Bonitron 功能描述:OVERVOLTAGE BRAKING RESISTOR |
發布緊急采購，3分鐘左右您將得到回復。