![](http://datasheet.mmic.net.cn/30000/M30280M8V-XXXHP_datasheet_2358818/M30280M8V-XXXHP_196.png)
14.Serial I/O
).
r
e
v
-
V
/.
r
e
v
-
T
(
p
u
o
r
G
8
2
/
C
6
1
M
page 176
0
9
3
f
o
7
0
2
,
0
3
.r
a
M
0
1
.
1
.
v
e
R
0
1
0
-
7
8
2
0
B
9
0
J
E
R
Item
Specification
Transfer data format
Character bit (transfer data): Selectable from 7, 8 or 9 bits
Start bit: 1 bit
Parity bit: Selectable from odd, even, or none
Stop bit: Selectable from 1 or 2 bits
Transfer clock
The CKDIR bit in the UiMR(i=0 to 2) register is set to 0 (internal clock) : fj/ (16(n+1))
fj = f1SIO, f2SIO, f8SIO, f32SIO. n: Setting value of UiBRG register
0016 to FF16
CKDIR bit is set to “1” (external clock ) : fEXT/16(n+1)
fEXT: Input from CLKi pin. n :Setting value of UiBRG register
0016 to FF16
Transmission, reception control
_______
_______ _______
Selectable from CTS function, RTS function or CTS/RTS function disable
Transmission start condition Before transmission can start, the following requirements must be met
_ The TE bit in the UiC1 register is set to 1 (transmission enabled)
_ The TI bit in the UiC1 register is set to 0 (data present in UiTB register)
_______
_ If CTS function is selected, input on the CTSi pin is set to “L”
Reception start condition
Before reception can start, the following requirements must be met"
_ The RE bit in the UiC1 register is set to 1 (reception enabled)
_ Start bit detection
For transmission, one of the following conditions can be selected
_ The UiIRS bit (2) is set to 0 (transmit buffer empty): when transferring data from the
UiTB register to the UARTi transmit register (at start of transmission)
_ The UiIRS bit is set to1 (transfer completed): when the serial I/O finished sending
data from the UARTi transmit register
For reception
When transferring data from the UARTi receive register to the UiRB register (at
completion of reception)
Error detection
Overrun error (1)
This error occurs if the serial I/O started receiving the next data before reading the
UiRB register and received the bit one before the last stop bit in the the next data
Framing error
This error occurs when the number of stop bits set is not detected
Parity error
This error occurs when if parity is enabled, the number of 1 in parity and
character bits does not match the number of 1 set
Error sum flag
This flag is set to 1 when any of the overrun, framing, and parity errors is encountered
Select function
LSB first, MSB first selection
Whether to start sending/receiving data beginning with bit 0 or beginning with bit 7
can be selected
Serial data logic switch (UART2)
This function reverses the logic of the transmit/receive data. The start and stop bits
are not reversed.
TXD, RXD I/O polarity switch (UART2)
This function reverses the polarities of hte TXD pin output and RXD pin input. The
logic levels of all I/O data is reversed.
_______ _______
Separate CTS/RTS pins (UART0)
_________
CTS0 and RTS0 are input/output from separate pins
UART1 pin remapping selection
The UART1 pin can be selected from the P67 to P64 or P73 to P70
14.1.2 Clock Asynchronous Serial I/O (UART) Mode
The UART mode allows transmitting and receiving data after setting the desired transfer rate and transfer
data format. Tables 14.5 lists the specifications of the UART mode.
Table 14.5 UART Mode Specifications
Interrupt request
generation timing
NOTES:
1. If an overrun error occurs, bits 8 to 0 in the UiRB (i=0 to 2) register are undefined. The IR bit in the
SiRIC register remains unchanged.
2. Bits U0IRS and U1IRS respectively are the UCON register bits 0 and 1; the U2IRS bit is the U2C1
register bit 4.