參數資料
型號： M30102M3-XXXFP
元件分類： 微控制器/微處理器
英文描述： 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP48
封裝： 7 X 7 MM, 0.50 MM PITCH, PLASTIC, LQFP-48
文件頁數： 94/166頁
文件大?。?/td> 2060K
代理商： M30102M3-XXXFP
Oscillation Stop Detection
Under
development
Tentative Specifications REV.E1
Specifications in this manual are tentative and subject to change.
Mitsubishi microcomputers
M30100/M30102 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
30
Oscillation Stop Detection Function
The oscillation stop detection function detects abnormal stopping of the main clock by causes such as
opening and shorting of the XIN oscillation circuit. When oscillation stop is detected, an oscillation stop
detection interrupt is issued. When an oscillation stop detection interrupt is issued, the ring oscillator in the
microcomputer operates automatically and is used as the main clock in place of the XIN clock. This allows
interrupt processing.
The oscillation stop detection function can be enabled/disabled with bit 0 and bit 1 of the oscillation stop
detection register. When this bit is set to “112,” the function is enabled. After the reset is released, the
oscillation stop detection function becomes disabled because the bit value is “002.”
Table 1.10.1 gives an specification overview of the oscillation stop detection function, Figure 1.10.2 is a
configuration diagram of the oscillation stop detection circuit and Figure 1.10.3 shows the configuration of
the oscillation stop detection register.
Table 1.10.1. Specification overview of the oscillation stop detection function
Item
Specification
Oscillation stop detectable clock and
XIN
≥ 2 MHz
frequency bandwidth
Enabling condition for oscillation stop
When the oscillation stop detection bit (bit 0 of address 000C16)
detection function
and the oscillation stop detection interrupt enable bit (bit 1 of
address 000C16) are set to “1”
Operation at oscillation stop detection
Oscillation stop detection interrupt occurs
Notes on STOP mode, low power
Before stopping the main clock (XIN-XOUT), set the
dissipation mode, and ring oscillator
oscillation stop detection enable bit to “0” to disable the
mode
oscillation stop detection function. Enable main clock
(XIN-XOUT) oscillation and after the oscillation stabilizes,
set the bit to “1” again.
Notes on WAIT mode
If the peripheral function clock is stopped in WAIT mode
with the WAIT mode peripheral function clock stop bit
(bit 2 of the address 000616), oscillation stop will be detected.
Do not stop the peripheral function clock in WAIT mode.
相關PDF資料
PDF描述
M30100M2T-XXXFP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP32
M30102M3T-XXXFP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP48
M30100M2-XXXFP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP32
M30100F3TFP 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP32
M30100M3-XXXFP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP32
相關代理商/技術參數
參數描述
M30102T-PTC 制造商:Renesas Electronics Corporation 功能描述:DEV 48PIN .5MM QFP CNVTR FOR M30100T-PRB - Bulk
M30-1050046 功能描述:集管和線殼 FML CRIMP CONTACT 1.25MM,AWG 26-30, RL RoHS:否 產品種類:1.0MM Rectangular Connectors 產品類型:Headers - Pin Strip 系列:DF50 觸點類型:Pin (Male) 節距:1 mm 位置/觸點數量:16 排數:1 安裝風格:SMD/SMT 安裝角:Right 端接類型:Solder 外殼材料:Liquid Crystal Polymer (LCP) 觸點材料:Brass 觸點電鍍:Gold 制造商:Hirose Connector
M30-1060046 功能描述:集管和線殼 FML CRIMP CONTACT 1.25MM,AWG 26-30,LSE RoHS:否 產品種類:1.0MM Rectangular Connectors 產品類型:Headers - Pin Strip 系列:DF50 觸點類型:Pin (Male) 節距:1 mm 位置/觸點數量:16 排數:1 安裝風格:SMD/SMT 安裝角:Right 端接類型:Solder 外殼材料:Liquid Crystal Polymer (LCP) 觸點材料:Brass 觸點電鍍:Gold 制造商:Hirose Connector
M3010A 制造商:Honeywell Sensing and Control 功能描述:GENERAL MARKET VRS
M3010A25 制造商:Honeywell Sensing and Control 功能描述:GENERAL MARKET VRS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*