- 您現在的位置：買賣IC網 > PDF目錄44996 > LTC4270AIUKG#TRPBF (LINEAR TECHNOLOGY CORP) SPECIALTY ANALOG CIRCUIT, PQCC52 PDF資料下載
參數資料
| 型號： | LTC4270AIUKG#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQCC52 |
| 封裝： | 8 X 7 MM, LEAD FREE, PLASTIC, QFN-52 |
| 文件頁數： | 8/32頁 |
| 文件大?。?/td> | 344K |
| 代理商： | LTC4270AIUKG#TRPBF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC4270/LTC4271
16
42701fa
The LTC4270/LTC4271 chipset implements a proprietary
isolation scheme for inter-chip communication. This
architecture dramatically reduces BOM cost by replacing
expensive opto-isolators and isolated power supplies with
a single low-cost transformer.
The LTC4270/LTC4271 comes in three grades which sup-
port different PD power levels.
The A-grade LTC4270/LTC4271 chipset extends PoE
power delivery capabilities to LTPoE++ levels. LTPoE++
is a Linear Technology proprietary specification allowing
for the delivery of up to 90W to LTPoE++ compliant PDs.
The LTPoE++ architecture extends the IEEE physical power
negotiation to include 35W, 45W, 70W and 90W power
levels. The A-grade LTC4270/LTC4271 also incorporates
all B- and C-grade features.
The B-grade LTC4270/LTC4271 is a fully IEEE-compliant
Type 2 PSE supporting autonomous detection, classifica-
tion and powering of Type 1 and Type 2 PDs. The B-grade
LTC4270/LTC4271 also incorporates all C-grade features.
The C-grade LTC4270/LTC4271 is a fully autonomous
802.3af Type 1 PSE solution. Intended for use only with
the AUTO pin tied high, the C-grade chipset autonomously
supports detection, classification and powering of Type 1
PDs. As a Type 1 PSE, two event classification is prohibited
and Class 4 PDs are automatically treated as Class 0 PDs.
PoE BASICS
Common Ethernet data connections consist of two or four
twisted pairs of copper wire (commonly known as CAT-5
cable), transformer-coupled at each end to avoid ground
loops. PoE systems take advantage of this coupling ar-
rangement by applying voltage between the center-taps
of the data transformers to transmit power from the PSE
to the PD without affecting data transmission. Figure 10
shows a high level PoE system schematic.
To avoid damaging legacy data equipment that does not
expect to see DC voltage, the PoE spec defines a protocol
that determines when the PSE may apply and remove
power. Valid PDs are required to have a specific 25k com-
mon mode resistance at their input. When such a PD is
connected to the cable, the PSE detects this signature
APPLICATIONS INFORMATION
resistance and turns on the power. When the PD is later
disconnected, the PSE senses the open circuit and turns
power off. The PSE also turns off power in the event of a
current fault or short circuit.
When a PD is detected, the PSE optionally looks for a
classification signature that tells the PSE the maximum
power the PD will draw. The PSE can use this information
to allocate power among several ports, to police the current
consumption of the PD, or to reject a PD that will draw more
power than the PSE has available. The classification step
is optional; if a PSE chooses not to classify a PD, it must
assume that the PD is a 13W (full 802.3af power) device.
New in 802.3at
The newer 802.3at standard supersedes 802.3af and brings
several new features:
A PD may draw as much as 25.5W. Such PDs (and the
PSEs that support them) are known as Type 2. Older
13W 802.3af equipment is classified as Type 1. Type 1
PDs will work with all PSEs; Type 2 PDs may require
Type 2 PSEs to work properly. The LTC4270/LTC4271
is designed to work in both Type 1 and Type 2 PSE de-
signs, and also supports non-standard configurations
at higher power levels.
The Classification protocol is expanded to allow Type 2
PSEs to detect Type 2 PDs, and to allow Type 2 PDs to
determine if they are connected to a Type 2 PSE. Two
versions of the new Classification protocol are avail-
able: an expanded version of the 802.3af Class Pulse
protocol, and an alternate method integrated with the
existing LLDP protocol (using the Ethernet data path).
The LTC4270/LTC4271 fully supports the new Class
Pulse protocol and is also compatible with the LLDP
protocol (which is implemented in the data communica-
tions layer, not in the PoE circuitry).
Fault protection current levels and timing are adjusted
to reduce peak power in the MOSFET during a fault; this
allows the new 25.5W power levels to be reached using
the same MOSFETs as older 13W designs.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4270AIUKG#PBF | SPECIALTY ANALOG CIRCUIT, PQCC52 |
| LTC4274CIUHF#PBF | POWER SUPPLY MANAGEMENT CKT, PQCC38 |
| LTC4274AIUHF-4#TRPBF | POWER SUPPLY MANAGEMENT CKT, PQCC38 |
| LTC4274AIUHF-3#PBF | POWER SUPPLY MANAGEMENT CKT, PQCC38 |
| LTC4274AIUHF-2#TRPBF | POWER SUPPLY MANAGEMENT CKT, PQCC38 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4270BIUKG#PBF | 制造商:Linear Technology 功能描述:POE Controller 25.5W 52-Pin QFN EP 制造商:Linear Technology 功能描述:Bulk 制造商:Linear Technology 功能描述:IC POE LTPOE 12-PORT PSE 52-QFN 制造商:Linear Technology 功能描述:IC PSE CONTROLLER 3.3V QFN-52 制造商:Linear Technology 功能描述:PSE CNTRL 12 PORT 25.5W 1M 制造商:Linear Technology 功能描述:IC, PSE CONTROLLER, 3.3V, QFN-52; Input Voltage:3.3V; Supply Current:10mA; UVLO:25V; Digital IC Case Style:QFN; No. of Pins:52; Frequency:1MHz; Operating Temperature Min:-40C; Operating Temperature Max:85C; Package / Case:52-QFN ;RoHS Compliant: Yes |
| LTC4270BIUKG#PBF | 制造商:Linear Technology 功能描述:IC, PSE CONTROLLER, 3.3V, QFN-52 |
| LTC4270BIUKG#TRPBF | 制造商:Linear Technology 功能描述:POE Controller 25.5W 52-Pin QFN EP 制造商:Linear Technology 功能描述:PSE CONTROLLER, 12PORT, 57V, QFN-52; Supply Current:10mA; UVLO:25V; Digital IC Case Style:QFN; No. of Pins:52; Duty Cycle (%):6.3%; Frequency:1MHz; Operating Temperature Min:-40C; Operating Temperature Max:85C ;RoHS Compliant: Yes |
| LTC4270CIUKG#PBF | 制造商:Linear Technology 功能描述:POE Controller 13W 52-Pin QFN EP 制造商:Linear Technology 功能描述:IC POE LTPOE 12-PORT PSE 52-QFN 制造商:Linear Technology 功能描述:PSE CNTRL 12 PORT 13W 1MHZ 制造商:Linear Technology 功能描述:IC PSE CONTROLLER 3.3V QFN-52 制造商:Linear Technology 功能描述:IC, PSE CONTROLLER, 3.3V, QFN-52; Input Voltage:3.3V; Supply Current:10mA; UVLO:25V; Digital IC Case Style:QFN; No. of Pins:52; Frequency:1MHz; Operating Temperature Min:-40C; Operating Temperature Max:85C; Package / Case:52-QFN ;RoHS Compliant: Yes |
| LTC4270CIUKG#PBF | 制造商:Linear Technology 功能描述:IC PSE CONTROLLER 3.3V QFN-52 制造商:Linear Technology 功能描述:IC, PSE CONTROLLER, 3.3V, QFN-52 |
發布緊急采購，3分鐘左右您將得到回復。