參數資料
型號： LTC2422
廠商： Linear Technology Corporation
英文描述： 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10
中文描述： 1-/2-Channel 20位ADC的無延遲UPower采用MSOP - 10
文件頁數： 15/32頁
文件大?。?/td> 375K
代理商： LTC2422
15
LTC2421/LTC2422
24212f
interface with other devices. If CS is LOW during the con-
vert or sleep state, SDO will output EOC. If CS is LOW
during the conversion phase, the EOC bit appears HIGH on
the SDO pin. Once the conversion is complete, EOC goes
LOW. The device remains in the sleep state until the first
rising edge of SCK occurs while CS = 0. While in the sleep
state, the device is in a LOW power state if CS is HIGH.
Chip Select Input (CS)
The active LOW chip select, CS (Pin 7), is used to test the
conversion status and to enable the data output transfer as
described in the previous sections.
In addition, the CS signal can be used to trigger a new
conversion cycle before the entire serial data transfer has
been completed. The LTC2421/LTC2422 will abort any
serial data transfer in progress and start a new conversion
cycle anytime a LOW-to-HIGH transition is detected at the
CS pin after the converter has entered the data output state
(i.e., after the first rising edge of SCK occurs with CS = 0).
Finally, CS can be used to control the free-running modes
of operation, see Serial Interface Timing Modes section.
Grounding CS will force the ADC to continuously convert
at the maximum output rate selected by F
O
. Tying a ca-
pacitor to CS will reduce the output rate and power dissi-
pation by a factor proportional to the capacitor’s value,
see Figures 13 to 15.
SERIAL INTERFACE TIMING MODES
The LTC2421/LTC2422’s 3-wire interface is SPI and
MICROWIRE compatible. This interface offers several
flexible modes of operation. These include internal/exter-
nal serial clock, 2- or 3-wire I/O, single cycle conversion
and autostart. The following sections describe each of
these serial interface timing modes in detail. In all these
cases, the converter can use the internal oscillator (F
O
=
LOW or F
O
= HIGH) or an external oscillator connected to
the F
O
pin. Refer to Table 4 for a summary.
External Serial Clock, Single Cycle Operation
(SPI/MICROWIRE Compatible)
This timing mode uses an external serial clock to shift out
the conversion result and a CS signal to monitor and con-
trol the state of the conversion cycle, see Figure 6.
The serial clock mode is selected on the falling edge of CS.
To select the external serial clock mode, the serial clock pin
(SCK) must be LOW during each CS falling edge.
The serial data output pin (SDO) is Hi-Z as long as CS is
HIGH. At any time during the conversion cycle, CS may be
pulled LOW in order to monitor the state of the converter.
While CS is LOW, EOC is output to the SDO pin. EOC = 1
while a conversion is in progress and EOC = 0 if the device
is in the sleep state. Independent of CS, the device auto-
matically enters the sleep state once the conversion is
complete. While in the sleep state, power is reduced an
order of magnitude if CS is HIGH.
When the device is in the sleep state (EOC = 0), its
conversion result is held in an internal static shift register.
The device remains in the sleep state until the first rising
edge of SCK is seen while CS is LOW. Data is shifted out
the SDO pin on each falling edge of SCK. This enables
external circuitry to latch the output on the rising edge of
SCK. EOC can be latched on the first rising edge of SCK
and the last bit of the conversion result can be latched on
the 24th rising edge of SCK. On the 24th falling edge of
SCK, the device begins a new conversion. SDO goes HIGH
(EOC = 1) indicating a conversion is in progress.
Table 4. LTC2421/LTC2422 Interface Timing Modes
Conversion
Cycle
Control
CS and SCK
SCK
CS
↓
Continuous
C
EXT
Data
Output
Control
CS and SCK
SCK
CS
↓
Internal
Internal
Connection
and
Waveforms
Figures 6, 7
Figure 8
Figures 9, 10
Figure 11
Figure 12
SCK
Source
External
External
Internal
Internal
Internal
Configuration
External SCK, Single Cycle Conversion
External SCK, 2-Wire I/O
Internal SCK, Single Cycle Conversion
Internal SCK, 2-Wire I/O, Continuous Conversion
Internal SCK, Autostart Conversion
APPLICATIOU
W
U
U
相關PDF資料
PDF描述
LTUX 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10
LTUY 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10
LTUZ 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10
LTVA 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10
LTC2450 Easy-to-Use, Ultra-Tiny 16-Bit ADC
相關代理商/技術參數
參數描述
LTC2422CMS 功能描述:IC ADC 2CH 20BIT MICRPWR 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC2422CMS#PBF 功能描述:IC ADC 2CH 20BIT MICRPWR 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
LTC2422CMS#TR 功能描述:IC ADC 2CH 20BIT MICRPWR 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC2422CMS#TRPBF 功能描述:IC ADC 2CH 20BIT MICRPWR 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC2422CMSPBF 制造商:Linear Technology 功能描述:ADC,LTC2422C 20bit D-S 2 ch SPI MSOP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*