參數資料
型號： LTC2422
廠商： Linear Technology Corporation
英文描述： 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10
中文描述： 1-/2-Channel 20位ADC的無延遲UPower采用MSOP - 10
文件頁數： 11/32頁
文件大?。?/td> 375K
代理商： LTC2422
11
LTC2421/LTC2422
24212f
Conversion Clock
A major advantage delta-sigma converters offer over con-
ventional type converters is an on-chip digital filter (com-
monly known as Sinc or Comb filter). For high resolution,
low frequency applications, this filter is typically designed
to reject line frequencies of 50Hz or 60Hz plus their har-
monics. In order to reject these frequencies in excess of
110dB, a highly accurate conversion clock is required. The
LTC2421/LTC2422 incorporate an on-chip highly accu-
rate oscillator. This eliminates the need for external fre-
quency setting components such as crystals or oscilla-
tors. Clocked by the on-chip oscillator, the LTC2421/
LTC2422 reject line frequencies (50Hz or 60Hz
±
2%) a
minimum of 110dB.
Ease of Use
The LTC2421/LTC2422 data output has no latency, filter
settling or redundant data associated with the conver-
sion cycle. There is a one-to-one correspondence be-
tween the conversion and the output data. Therefore,
multiplexing an analog input voltage is easy.
The LTC2421/LTC2422 perform offset and full-scale cali-
brations every conversion cycle. This calibration is trans-
parent to the user and has no effect on the cyclic operation
described above. The advantage of continuous calibration
is extreme stability of offset and full-scale readings with
respect to time, supply voltage change and temperature
drift.
Power-Up Sequence
The LTC2421/LTC2422 automatically enter an internal reset
state when the power supply voltage V
CC
drops below
approximately 2.2V. This feature guarantees the integrity
of the conversion result and of the serial interface mode
selection which is performed at the initial power-up. (See
the 2-wire I/O sections in the Serial Interface Timing Modes
section.)
When the V
CC
voltage rises above this critical threshold,
the converter creates an internal power-on-reset (POR)
signal with duration of approximately 0.5ms. The POR
signal clears all internal registers. Following the POR sig-
nal, the LTC2421/LTC2422 start a normal conversion cycle
and follows the normal succession of states described
APPLICATIOU
W
U
U
above. The first conversion result following POR is accu-
rate within the specifications of the device.
Reference Voltage Range
The LTC2421/LTC2422 can accept a reference voltage
(V
REF
= FS
SET
– ZS
SET
)
from 0V to V
CC
. The converter output
noise is determined by the thermal noise of the front-end
circuits, and as such, its value in microvolts is nearly con-
stant with reference voltage. A decrease in reference volt-
age will not significantly improve the converter’s effective
resolution. On the other hand, a reduced reference voltage
will improve the overall converter INL performance. The
recommended range for the LTC2421/LTC2422 voltage
reference is 100mV to V
CC
.
Input Voltage Range
The converter is able to accommodate system level offset
and gain errors as well as system level overrange situa-
tions due to its extended input range, see Figure 3. The
LTC2421/LTC2422 convert input signals within the ex-
tended input range of –0.125 V
REF
to 1.125 V
REF
(V
REF
= FS
SET
– ZS
SET
).
For large values of V
REF
(V
REF
= FS
SET
– ZS
SET
),
this range
is limited by the absolute maximum voltage range of
–0.3V to (V
CC
+ 0.3V). Beyond this range, the input ESD
protection devices begin to turn on and the errors due to
the input leakage current increase rapidly.
Input signals applied to V
IN
may extend below ground by
–300mV and above V
CC
by 300mV. In order to limit any
Figure 3. LTC2421/LTC2422 Input Range
24212 F03
V
CC
+ 0.3V
FS
SET
+ 0.12V
REF
FS
SET
–0.3V
(V
REF
= FS
SET
– ZS
SET
)
ZS
SET
– 0.12V
REF
ZS
SET
NORMAL
INPUT
RANGE
EXTENDED
INPUT
RANGE
ABSOLUTE
MAXIMUM
INPUT
RANGE
相關PDF資料
PDF描述
LTUX 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10
LTUY 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10
LTUZ 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10
LTVA 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10
LTC2450 Easy-to-Use, Ultra-Tiny 16-Bit ADC
相關代理商/技術參數
參數描述
LTC2422CMS 功能描述:IC ADC 2CH 20BIT MICRPWR 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC2422CMS#PBF 功能描述:IC ADC 2CH 20BIT MICRPWR 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
LTC2422CMS#TR 功能描述:IC ADC 2CH 20BIT MICRPWR 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC2422CMS#TRPBF 功能描述:IC ADC 2CH 20BIT MICRPWR 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC2422CMSPBF 制造商:Linear Technology 功能描述:ADC,LTC2422C 20bit D-S 2 ch SPI MSOP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*