- 您現在的位置：買賣IC網 > PDF目錄384633 > LTC2422 (Linear Technology Corporation) 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10 PDF資料下載
參數資料
| 型號： | LTC2422 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10 |
| 中文描述： | 1-/2-Channel 20位ADC的無延遲UPower采用MSOP - 10 |
| 文件頁數： | 14/32頁 |
| 文件大?。?/td> | 375K |
| 代理商： | LTC2422 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
14
LTC2421/LTC2422
24212f
external serial clock. If the change occurs during the con-
version state, the result of the conversion in progress may
be outside specifications but the following conversions
will not be affected. If the change occurs during the data
output state and the converter is in the Internal SCK mode,
the serial clock duty cycle may be affected but the serial
data stream will remain valid.
Table 3 summarizes the duration of each state as a func-
tion of F
O
.
SERIAL INTERFACE
The LTC2421/LTC2422 transmit the conversion results
and receives the start of conversion command through a
synchronous 3-wire interface. During the conversion and
sleep states, this interface can be used to assess the con-
verter status and during the data output state, it is used to
read the conversion result.
Serial Clock Input/Output (SCK)
The serial clock signal present on SCK (Pin 9) is used to
synchronize the data transfer. Each bit of data is shifted out
the SDO pin on the falling edge of the serial clock.
In the Internal SCK mode of operation, the SCK pin is an
output and the LTC2421/LTC2422 create their own serial
clock by dividing the internal conversion clock by 8. In the
External SCK mode of operation, the SCK pin is used as
input. The internal or external SCK mode is selected on
power-up and then reselected every time a HIGH-to-LOW
transition is detected at the CS pin. If SCK is HIGH or
floating at power-up or during this transition, the con-
verter enters the internal SCK mode. If SCK is LOW at
power-up or during this transition, the converter enters
the external SCK mode.
Serial Data Output (SDO)
The serial data output pin, SDO (Pin 8), drives the serial
data during the data output state. In addition, the SDO pin
is used as an end of conversion indicator during the con-
version and sleep states.
When CS (Pin 7) is HIGH, the SDO driver is switched to a
high impedance state. This allows sharing the serial
Table 3. LTC2421/LTC2422 State Duration
State
Operating Mode
CONVERT
Internal Oscillator
Duration
133ms
F
O
= LOW
(60Hz Rejection)
F
O
= HIGH
(50Hz Rejection)
F
O
= External Oscillator
with Frequency f
EOSC
kHz
(f
EOSC
/2560 Rejection)
160ms
External Oscillator
20510/f
EOSC
s
SLEEP
DATA OUTPUT
As Long As CS = HIGH Until CS = 0 and SCK
As Long As CS = LOW But Not Longer Than 1.28ms
(24 SCK cycles)
As Long As CS = LOW But Not Longer Than 192/f
EOSC
ms
(24 SCK cycles)
As Long As CS = LOW But Not Longer Than 24/f
SCK
ms
(24 SCK cycles)
Internal Serial Clock
F
O
= LOW/HIGH
(Internal Oscillator)
F
O
= External Oscillator with
Frequency f
EOSC
kHz
External Serial Clock with
Frequency f
SCK
kHz
APPLICATIOU
W
U
U
Figure 5. LTC2421/LTC2422 Normal Mode Rejection When
Using an External Oscillator of Frequency f
EOSC
INPUT FREQUENCY DEVIATION FROM NOTCH FREQUENCY (%)
–12
–8
–4
0
4
8
12
R
24212 F05
–60
–70
–80
–90
–100
–110
–120
–130
–140
相關PDF資料 |
PDF描述 |
|---|---|
| LTUX | 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10 |
| LTUY | 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10 |
| LTUZ | 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10 |
| LTVA | 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10 |
| LTC2450 | Easy-to-Use, Ultra-Tiny 16-Bit ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2422CMS | 功能描述:IC ADC 2CH 20BIT MICRPWR 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2422CMS#PBF | 功能描述:IC ADC 2CH 20BIT MICRPWR 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2422CMS#TR | 功能描述:IC ADC 2CH 20BIT MICRPWR 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2422CMS#TRPBF | 功能描述:IC ADC 2CH 20BIT MICRPWR 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2422CMSPBF | 制造商:Linear Technology 功能描述:ADC,LTC2422C 20bit D-S 2 ch SPI MSOP |
發布緊急采購，3分鐘左右您將得到回復。