- 您現在的位置：買賣IC網 > PDF目錄385505 > LTC1705 (Linear Technology Corporation) Dual 550kHz Synchronous Switching Regulator Controller with 5-Bit VID and 150mA LDO PDF資料下載
參數資料
| 型號： | LTC1705 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Dual 550kHz Synchronous Switching Regulator Controller with 5-Bit VID and 150mA LDO |
| 中文描述： | 雙550kHz的同步開關，5位VID和150mA LDO穩壓器控制器 |
| 文件頁數： | 8/28頁 |
| 文件大?。?/td> | 326K |
| 代理商： | LTC1705 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC1705
8
RUN/SS (Pin 9):
SoftStart. Pulling RUN/SS to GND exter-
nally shuts down the LTC1705 and turns off all the external
MOSFET switches. The quiescent supply current drops
below 100
μ
A. A capacitor from RUN/SS to GND controls
the turn on time and rate of rise of the core and I/O output
voltages at power up. An internal 3
μ
A current source pull-
up at RUN/SS sets the turn-on time at approximately
300ms/
μ
F.
COMPC (Pin 10):
Core Controller Loop Compensation.
The COMPC pin is connected directly to the output of the
Core controller’s error amplifier and the input of the PWM
comparator. Use an RC network between the COMPC pin
and the FBC pin to compensate the feedback loop for
optimum transient response.
FBC (Pin 11):
Core Controller Feedback Input. Connect the
loop compensation network for the core controller to FBC.
FBC internally connects to the VID resistor network to set
the Core output voltage.
GND (Pin 12):
Signal Ground. All internal low power
circuitry returns to the GND pin. Connect to a low imped-
ance ground, separated from the PGND node. All feed-
back, compensation and softstart connections should
return to GND. GND and PGND should connect only at a
single point, near the PGND pin and the negative plate of
the V
IN
bypass capacitor.
SENSEC (Pin 13):
Core Controller Output Sense. Connect
to V
OUTC
.
VID0 to VID4 (Pins 14 to 18):
VID Programming Inputs.
These are logic inputs that set the output voltage at the
Core supply to a preprogrammed value (see Table 1). VID4
is the MSB, VID0 is the LSB. The codes selected by the VID
inputs correspond to the Intel Mobile VID specification.
Any VID code transition forces PGOOD to go low for 20
μ
s.
Each VID pin includes an on-chip 30k pull-up resistor in
series with a diode (see Block Diagram).
V
CC
(Pin 19):
Power Supply Input. All internal circuits
except the output drivers are powered from this pin.
Connect V
CC
to a low-noise 5V supply and bypass the pin
to GND with at least a 10
μ
F capacitor in close proximity to
the LTC1705.
PIU
FBIO (Pin 20):
I/O Controller Feedback Input. Connect
FBIO through a resistor divider network to V
OUTIO
to set the
output voltage. Also, connect the loop compensation
network for the I/O controller to FBIO.
COMPIO (Pin 21):
I/O Controller Loop Compensation. See
COMPC.
PGOOD (Pin 22):
Power Good. PGOOD is an open-drain
logic output. PGOOD pulls low if any of the three supply
outputs are out of regulation (see Electrical Characteris-
tics table for Core, I/O and CLK thresholds). An external
pull-up resistor is required at PGOOD to allow it to swing
positive.
V
OUTCLK
(Pin 23):
Clock Supply Output. V
OUTCLK
is the
output node of the internal linear clock supply regulator.
V
OUTCLK
provides up to 150mA at the 2.5V output to power
the CPU CLK supply. Bypass V
OUTCLK
with at least a 2.2
μ
F
capacitor to GND (refer to the V
CLK
Linear Regulator
section). If RUN/SS goes low, the V
OUTCLK
regulator shuts
down.
V
INCLK
(Pin 24):
Clock Supply Input. V
INCLK
is the input
terminal to the internal linear CLK supply regulator. Con-
nect V
INCLK
to a 3.3V supply to maximize efficiency. V
INCLK
can be connected to the 5V supply, but the efficiency of the
V
OUTCLK
regulator is reduced. Bypass V
INCLK
with a 10
μ
F
capacitor to GND.
SWIO (Pin 25):
I/O Controller Switching Node. See SWC.
TGIO (Pin 26):
I/O Controller Top Gate Drive. See TGC.
TGIO is designed to typically drive up to 2,000pF of gate
capacitance.
BOOSTIO (Pin 27):
I/O Controller Top Gate Driver Power.
See BOOSTC.
BGIO (Pin 28):
I/O Controller Bottom Gate Drive. See BGC.
BGIO is designed to typically drive up to 2,000pF of gate
capacitance.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1705EGN | Dual 550kHz Synchronous Switching Regulator Controller with 5-Bit VID and 150mA LDO |
| LTC1710 | Synchronous 8-Bit Up/Down Binary Counters 24-PDIP 0 to 70 |
| LTC1710C | Synchronous 8-Bit Up/Down Binary Counters 24-PDIP 0 to 70 |
| LTC1710CMS8 | Dual 16-By-4 Register Files 24-SOIC 0 to 70 |
| LTC1710CS8 | SMBus Dual Monolithic High Side Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1705EGN | 功能描述:IC PWR SUPPLY CONTROLLER 28SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC1705EGN#PBF | 功能描述:IC PWR SUPPLY CONTROLLER 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC1705EGN#TR | 功能描述:IC PWR SUPPLY CONTROLLER 28SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC1705EGN#TRPBF | 功能描述:IC PWR SUPPLY CONTROLLER 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC1706CS8-19 | 功能描述:IC VID VOLTAGE PROGRAMMER 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。