- 您現在的位置：買賣IC網 > PDF目錄44985 > LT3652EDD#TRPBF (LINEAR TECHNOLOGY CORP) 3 A BATTERY CHARGE CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO12 PDF資料下載
參數資料
| 型號： | LT3652EDD#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 3 A BATTERY CHARGE CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO12 |
| 封裝： | 3 X 3 MM, LEAD FREE, PLASTIC, DFN-12 |
| 文件頁數： | 6/26頁 |
| 文件大?。?/td> | 253K |
| 代理商： | LT3652EDD#TRPBF |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
LT3652
14
3652fc
APPLICATIONS INFORMATION
Magnetics vendors typically specify inductors with
maximum RMS and saturation current ratings. Select an
inductor that has a saturation current rating at or above (1+
ΔIMAX/2) ICHG(MAX), and an RMS rating above ICHG(MAX).
Inductors must also meet a maximum volt-second product
requirement. If this specification is not in the data sheet of
an inductor, consult the vendor to make sure the maximum
volt-second product is not being exceeded by your design.
The minimum required volt-second product is:
VBAT(FLT) (1 – VBAT(FLT)/VIN(MAX)) (V μS)
Rectifier Selection
The rectifier diode from SW to GND, in a LT3652 battery
charger provides a current path for the inductor current
when the main power switch is disabled. The rectifier is
selected based upon forward voltage, reverse voltage, and
maximum current. A Schottky diode is required, as low
Figure 3. 7.2V at 1.5A Switched Inductor Values
MAXIMUM OPERATIONAL VIN VOLTAGE (V)
12
16
4
SWITCHED
INDUCTOR
V
ALUE
(μH)
12
10
14
16
32
3652 F03
8
6
24
20
28
Figure 4. Feedback Resistors from BAT to VFB
Program Float Voltage
BAT
+
VFB
RFB2
RFB1
LT3652
3652 F04
forward voltage yields the lowest power loss and highest
efficiency. The rectifier diode must be rated to withstand
reverse voltages greater than the maximum VIN voltage.
The minimum average diode current rating (IDIODE(MAX))
is calculated with maximum output current (ICHG(MAX)),
maximum operational VIN, and output at the precondition
threshold (VBAT(PRE), or 0.7 VBAT(FLT)):
IDIODE(MAX) > ICHG(MAX) (VIN(MAX) – VBAT(PRE)) / VIN(MAX)) (A)
For example, a rectifier diode for a 7.2V, 2A charger with
a 25V maximum input voltage would require:
IDIODE(MAX) > 2 (25 – 0.7[7.2]) / 25), or
IDIODE(MAX) > 1.6A
Battery Float Voltage Programming
The output battery float voltage (VBAT(FLT)) is programmed
by connecting a resistor divider from the BAT pin to VFB.
VBAT(FLT) can be programmed up to 14.4V.
相關PDF資料 |
PDF描述 |
|---|---|
| LT3652HVEDD#PBF | BATTERY CHARGE CONTROLLER, PDSO12 |
| LT3652HVEMSE#TRPBF | BATTERY CHARGE CONTROLLER, PDSO12 |
| LT3652HVEDD#TRPBF | BATTERY CHARGE CONTROLLER, PDSO12 |
| LT3663EMS8E-3.3#PBF | 2.5 A SWITCHING REGULATOR, 1100 kHz SWITCHING FREQ-MAX, PDSO8 |
| LT3663IMS8E-3.3#PBF | 2.5 A SWITCHING REGULATOR, 1100 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3652EMSE | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Power Tracking 2A Battery Charger for Solar Power |
| LT3652EMSE#PBF | 功能描述:IC BATTERY CHARGER SOLAR 12MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LT3652EMSE#PBF | 制造商:Linear Technology 功能描述:BATTERY CHARGER FOR SOLAR POWER 制造商:Linear Technology 功能描述:IC, BATTERY CHARGER, 2A, MSOP-12 |
| LT3652EMSE#TRPBF | 功能描述:IC BATT CHARGER SOLAR 2A 12MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LT3652EMSEPBF | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion 2A 4.2V MSOP12EP |
發布緊急采購，3分鐘左右您將得到回復。