- 您現在的位置：買賣IC網 > PDF目錄44985 > LT3652EDD#TRPBF (LINEAR TECHNOLOGY CORP) 3 A BATTERY CHARGE CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO12 PDF資料下載
參數資料
| 型號： | LT3652EDD#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 3 A BATTERY CHARGE CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO12 |
| 封裝： | 3 X 3 MM, LEAD FREE, PLASTIC, DFN-12 |
| 文件頁數： | 3/26頁 |
| 文件大?。?/td> | 253K |
| 代理商： | LT3652EDD#TRPBF |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
LT3652
11
3652fc
APPLICATIONS INFORMATION
The ITH error voltage corresponds linearly to average
current sensed across the inductor current sense resistor,
allowing maximum charge current control by limiting the
effective voltage range of ITH. A clamp limits this voltage
to 1V which, in turn, limits the current sense voltage to
100mV. This sets the maximum charge current, or the
current delivered while the charger is operating in con-
stant-current (CC) mode, which corresponds to 100mV
across RSENSE. The ITH voltage is pulled down to reduce
this maximum charge current should the voltage on the
VIN_REG pin falls below 2.7V (VIN_REG(TH)) or the die tem-
perature approaches 125°C.
If the voltage on the VFB pin is below 2.3V (VFB(PRE)),
the LT3652 engages precondition mode. During the
precondition interval, the charger continues to operate in
constant-current mode, but the maximum charge current
is reduced to 15% of the maximum programmed value
as set by RSENSE.
When the charger output voltage approaches the float volt-
age, or the voltage on the VFBpinapproaches3.3V(VFB(FLT)),
the charger transitions into constant-voltage (CV) mode
and charge current is reduced from the maximum value.
As this occurs, the ITH voltage falls from the limit clamp
and servos to lower voltages. The IC monitors the ITH volt-
age as it is reduced, and detection of C/10 charge current
is achieved when ITH = 0.1V. If the charger is configured
for C/10 termination, this threshold is used to terminate
the charge cycle. Once the charge cycle is terminated,
the CHRG status pin becomes high-impedance and the
charger enters low-current standby mode.
The LT3652 contains an internal charge cycle timer that
terminates a successful charge cycle after a programmed
amount of time. This timer is typically programmed to
achieve end-of-cycle (EOC) in 3 hours, but can be con-
figured for any amount of time by setting an appropriate
timing capacitor value (CTIMER). When timer termination
is used, the charge cycle does not terminate when C/10
is achieved. Because the CHRG status pin responds to
the C/10 current level, the IC will indicate a fully-charged
battery status, but the charger continues to source low
currents into the battery until the programmed EOC time
has elapsed, at which time the charge cycle will terminate.
At EOC when the charging cycle terminates, if the battery
did not achieve at least 97.5% of the full float voltage,
charging is deemed unsuccessful, the LT3652 re-initiates,
and charging continues for another full timer cycle.
Use of the timer function also enables bad-battery detec-
tion. This fault condition is achieved if the battery does
not respond to preconditioning, such that the charger
remains in (or enters) precondition mode after 1/8th of
the programmed charge cycle time. A bad battery fault
halts the charging cycle, the CHRG status pin goes high-
impedance, and the FAULT pin is pulled low.
When the LT3652 terminates a charging cycle, whether
through C/10 detection or by reaching timer EOC, the
average current mode analog loop remains active, but
the internal float voltage reference is reduced by 2.5%.
Because the voltage on a successfully charged battery is
at the full float voltage, the voltage error amp detects an
over-voltage condition and ITH is pulled low. When the
voltage error amp output drops below 0.3V, the IC enters
standby mode, where most of the internal circuitry is dis-
abled, and the VIN bias current is reduced to 85μA. When
the voltage on the VFB pin drops below the reduced float
reference level, the output of the voltage error amp will
climb, at which point the IC comes out of standby mode
and a new charging cycle is initiated.
VIN Input Supply
The LT3652 is biased directly from the charger input supply
through the VIN pin. This supply provides large switched
currents, so a high-quality, low ESR decoupling capacitor
is recommended to minimize voltage glitches on VIN. The
VIN decoupling capacitor (CVIN) absorbs all input switching
相關PDF資料 |
PDF描述 |
|---|---|
| LT3652HVEDD#PBF | BATTERY CHARGE CONTROLLER, PDSO12 |
| LT3652HVEMSE#TRPBF | BATTERY CHARGE CONTROLLER, PDSO12 |
| LT3652HVEDD#TRPBF | BATTERY CHARGE CONTROLLER, PDSO12 |
| LT3663EMS8E-3.3#PBF | 2.5 A SWITCHING REGULATOR, 1100 kHz SWITCHING FREQ-MAX, PDSO8 |
| LT3663IMS8E-3.3#PBF | 2.5 A SWITCHING REGULATOR, 1100 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3652EMSE | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Power Tracking 2A Battery Charger for Solar Power |
| LT3652EMSE#PBF | 功能描述:IC BATTERY CHARGER SOLAR 12MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LT3652EMSE#PBF | 制造商:Linear Technology 功能描述:BATTERY CHARGER FOR SOLAR POWER 制造商:Linear Technology 功能描述:IC, BATTERY CHARGER, 2A, MSOP-12 |
| LT3652EMSE#TRPBF | 功能描述:IC BATT CHARGER SOLAR 2A 12MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LT3652EMSEPBF | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion 2A 4.2V MSOP12EP |
發布緊急采購，3分鐘左右您將得到回復。