- 您現在的位置：買賣IC網 > PDF目錄44968 > LSM330DL (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBGA28 PDF資料下載
參數資料
| 型號： | LSM330DL |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA28 |
| 封裝： | 7.50 X 4.40 MM, 1.10 MM HEIGHT, GREEN, PLASTIC, LGA-28 |
| 文件頁數： | 9/54頁 |
| 文件大?。?/td> | 1064K |
| 代理商： | LSM330DL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
LSM330DL
Module specifications
Doc ID 022018 Rev 1
17/54
2.6
Terminology
2.6.1
Sensitivity
Linear acceleration sensitivity can be determined by applying 1
g acceleration to the device.
As the sensor can measure DC accelerations, this can be done easily by pointing the axis of
interest towards the center of the Earth, noting the output value, rotating the sensor by 180
degrees (point to the sky) and then noting the output value again. By doing so, ±1
g
acceleration is applied to the sensor. Subtracting the larger output value from the smaller
one, and dividing the result by 2, leads to the actual sensitivity of the sensor. This value
changes very little over temperature and also very little over time. The sensitivity tolerance
describes the range of sensitivities of a large population of sensors.
Angular rate sensitivity describes the angular rate gain of the sensor and can be determined
by applying a defined angular velocity to it. This value changes very little over temperature
and also very little over time.
2.6.2
Zero level
Linear acceleration zero-
g level offset (TyOff) describes the deviation of an actual output
signal from the ideal output signal if no acceleration is present. A sensor in a steady state on
a horizontal surface will measure 0
g on the X-axis and 0 g on the Y-axis whereas the Z-axis
will measure 1
g. The output is ideally in the middle of the dynamic range of the sensor
(content of OUT registers 00h, data expressed as 2’s complement number). A deviation
from the ideal value in this case is called zero-
g offset. Offset is to some extent a result of
stress to the MEMS sensor and therefore the offset can slightly change after mounting the
sensor onto a printed circuit board or exposing it to extensive mechanical stress. Offset
changes little over temperature, see “Zero-
g level change vs. temperature” (refer toTable 3).
The zero-
g level tolerance (TyOff) describes the standard deviation of the range of zero-g
levels of a population of sensors.
The angular rate zero-rate level describes the actual output value if there is no angular rate
present. Zero-rate level of precise MEMS sensors is, to some extent, a result of stress to the
sensor and therefore the zero-rate level can slightly change after mounting the sensor onto
a printed circuit board or after exposing it to extensive mechanical stress. This value
changes very little over temperature and also very little over time.
相關PDF資料 |
PDF描述 |
|---|---|
| LSN-0.75/16-D12HJ-C | 1-OUTPUT 12.8 W DC-DC REG PWR SUPPLY MODULE |
| LSN-1.8/16-D12HJ-C | 1-OUTPUT 28.8 W DC-DC REG PWR SUPPLY MODULE |
| LSN-1.2/16-D12HJ-C | 1-OUTPUT 19.2 W DC-DC REG PWR SUPPLY MODULE |
| LSN-2.5/16-D12HJ-C | 1-OUTPUT 40 W DC-DC REG PWR SUPPLY MODULE |
| LSN-1/16-D12HJ-C | 1-OUTPUT 16 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LSM330DLC | 功能描述:加速計 - 板上安裝 iNEMO 3D SIP Module 2.4V to 3.6V IO 1.8V RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LSM330DLCTR | 功能描述:加速計 - 板上安裝 iNEMO 3D SIP Module 2.4V to 3.6V IO 1.8V RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LSM330DLTR | 功能描述:加速計 - 板上安裝 Linear Sensor Module 3D ACC 3D Gyro RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LSM330DTR | 制造商:STMicroelectronics 功能描述:INEMO INERTIAL MODULE: 3D ACCELEROMETER AND 3D GYROSCOPE |
| LSM330TR | 功能描述:加速計 - 板上安裝 Inemo inertial module 3D accelerometer and 3D gyroscope RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
發布緊急采購，3分鐘左右您將得到回復。