- 您現在的位置：買賣IC網 > PDF目錄385487 > LM4881M (NATIONAL SEMICONDUCTOR CORP) Dual 200 mW Headphone Amplifier with Shutdown Mode PDF資料下載
參數資料
| 型號： | LM4881M |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | Dual 200 mW Headphone Amplifier with Shutdown Mode |
| 中文描述： | 0.3 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 9/11頁 |
| 文件大?。?/td> | 413K |
| 代理商： | LM4881M |
Application Information
(Continued)
shutdown function should be virtually clickless and popless.
While the device will function properly, (no oscillations or mo-
torboating), with C
equal to 0.1 μF, the device will be much
more susceptible to turn on clicks and pops. Thus, a value of
C
equal to 0.1 μF or larger is recommended in all but the
most cost sensitive designs.
AUDIO POWER AMPLIFIER DESIGN
Design a Dual 200mW/8
Audio Amplifier
Given:
Power Output
Load Impedance
Input Level
Input Impedance
Bandwidth
A designer must first determine the needed supply rail to ob-
tain the specified output power. Calculating the required sup-
ply rail involves knowing two parameters, V
the dropout voltage. The latter is typically 530 mV and can
be found from the graphs in the
Typical Performance Char-
acteristics.
V
OPEAK
can be determined from Equation 3.
200 mWrms
8
1 Vrms (max)
20 k
100 Hz–20 kHz
±
0.50 dB
(3)
For 200 mW of output power into an 8
load, the required
V
is 1.79 volts. A minimum supply rail of 2.32V results
from adding V
and V
. Since 5V is a standard supply
voltage in most applications, it is chosen for the supply rail.
Extra supply voltage creates headroom that allows the
LM4881 to reproduce peaks in excess of 200 mW without
clipping the signal.At this time, the designer must make sure
that the power supply choice along with the output imped-
ance does not violate the conditions explained in the
Power
Dissipation
section. Remember that the maximum power
dissipation point from Equation 1 must be multiplied by two
since there are two independent amplifiers inside the pack-
age.
Once the power dissipation equations have been addressed,
the required gain can be determined from Equation 4.
(4)
A
V
= R
f
/R
i
(5)
From Equation 4, the minimum gain is: A
V
= 1.26
Since the desired input impedance was 20 k
, and with a
gain of 1.26, a value of 27 k
is designated for R
, assuming
5% tolerance resistors. This combination results in a nominal
gain of 1.35. The final design step is to address the band-
width requirements which must be stated as a pair of 3 dB
frequency points. Five times away from a 3 dB point is
0.17 dB down from passband response assuming a single
pole roll-off. As stated in the
External Components
section,
both R
in conjunction with C
, and C
with R
, create first or-
der highpass filters. Thus to obtain the desired frequency low
response of 100 Hz within
±
0.5 dB, both poles must be
taken into consideration. The combination of two single order
filters at the same frequency forms a second order response.
This results in a signal which is down 0.34 dB at five times
away from the single order filter 3 dB point. Thus, a fre-
quency of 20 Hz is used in the following equations to ensure
that the response is better than 0.5 dB down at 100 Hz.
C
i
≥
1 / (2
π
* 20 k
* 20 Hz) = 0.397 μF; use 0.39 μF.
C
o
≥
1 / (2
π
* 8
* 20 Hz) = 995 μF; use 1000 μF.
The high frequency pole is determined by the product of the
desired high frequency pole, f
, and the closed-loop gain, A
V
. With a closed-loop gain of 1.35 and f
= 100 kHz, the re-
sulting GBWP = 135 kHz which is much smaller than the
LM4881 GBWP of 18 MHz. This figure displays that if a de-
signer has a need to design an amplifier with a higher gain,
the LM4881 can still be used without running into bandwidth
limitations.
www.national.com
9
相關PDF資料 |
PDF描述 |
|---|---|
| LM4881MM | Dual 200 mW Headphone Amplifier with Shutdown Mode |
| LM4881N | Dual 200 mW Headphone Amplifier with Shutdown Mode |
| LM4882 | 250mW Audio Power Amplifier with Shutdown Mode |
| LM4882M | 250mW Audio Power Amplifier with Shutdown Mode |
| LM4882MM | 250mW Audio Power Amplifier with Shutdown Mode |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4881M/NOPB | 功能描述:音頻放大器 BOOMER DUAL 200MW HEADPHONE AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4881MM | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4881MM/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4881MM/SL110729 | 制造商:Texas Instruments 功能描述: |
| LM4881MMX | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。