- 您現在的位置：買賣IC網 > PDF目錄384577 > JZ48F4L0QTZ (Intel Corp.) StrataFlash Wireless Memory PDF資料下載
參數資料
| 型號： | JZ48F4L0QTZ |
| 廠商： | Intel Corp. |
| 英文描述： | StrataFlash Wireless Memory |
| 中文描述： | 無線的StrataFlash存儲器 |
| 文件頁數： | 61/106頁 |
| 文件大?。?/td> | 1272K |
| 代理商： | JZ48F4L0QTZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁當前第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁
Intel StrataFlash Wireless Memory (L18)
Datasheet
Intel StrataFlash Wireless Memory (L18)
Order Number: 251902, Revision: 009
April 2005
61
WA0 must align with the start of an array buffer boundary
1
.
Buffered EFP considerations:
For optimum performance, cycling must be limited below 100 erase cycles per block
2
.
Buffered EFP programs one block at a time; all buffer data must fall within a single block
3
.
Buffered EFP cannot be suspended.
Programming to the flash memory array can occur only when the buffer is full
4
.
Read operation while performing Buffered EFP is not supported.
NOTES:
1.
Word buffer boundaries in the array are determined by A[4:0] (0x00 through 0x1F). The alignment start
point is A[4:0] = 0x00.
2.
Some degradation in performance may occur if this limit is exceeded, but the internal algorithm
continues to work properly.
3.
If the internal address counter increments beyond the block's maximum address, addressing wraps
around to the beginning of the block.
4.
If the number of words is less than 32, remaining locations must be filled with 0xFFFF.
11.3.2
Buffered EFP Setup Phase
After receiving the Buffered EFP Setup and Confirm command sequence, Status Register bit SR[7]
(Ready) is cleared, indicating that the WSM is busy with Buffered EFP algorithm startup. A delay
before checking SR[7] is required to allow the WSM enough time to perform all of its setups and
checks (Block-Lock status, V
PP
level, etc.). If an error is detected, SR[4] is set and Buffered EFP
operation terminates. If the block was found to be locked, SR[1] is also set. SR[3] is set if the error
occurred due to an incorrect V
PP
level.
Note:
Reading from the device after the Buffered EFP Setup and Confirm command sequence outputs
Status Register data. Do not issue the Read Status Register command; it will be interpreted as data
to be loaded into the buffer.
11.3.3
Buffered EFP Program/Verify Phase
After the Buffered EFP Setup Phase has completed, the host programming system must check
SR[7,0] to determine the availability of the write buffer for data streaming. SR[7] cleared indicates
the device is busy and the Buffered EFP program/verify phase is activated. SR[0] indicates the
write buffer is available.
Two basic sequences repeat in this phase: loading of the write buffer, followed by buffer data
programming to the array. For Buffered EFP, the count value for buffer loading is always the
maximum buffer size of 32 words. During the buffer-loading sequence, data is stored to sequential
buffer locations starting at address 0x00. Programming of the buffer contents to the flash memory
array starts as soon as the buffer is full. If the number of words is less than 32, the remaining buffer
locations must be filled with 0xFFFF.
Caution:
The buffer must be completely filled for programming to occur. Supplying an address outside of the
current block's range during a buffer-fill sequence causes the algorithm to exit immediately. Any
data previously loaded into the buffer during the fill cycle is not programmed into the array.
The starting address for data entry must be buffer size aligned, if not the Buffered EFP algorithm
will be aborted and the program fail (SR[4]) flag will be set.
相關PDF資料 |
PDF描述 |
|---|---|
| JZC-32F | SUBMINIATURE INTERMEDIATE POWER RELAY |
| KCA370UH | AM Tuner For Car Audio(汽車音響AM調諧器) |
| KCC1102A | Electronic AM/FM/MPX/Noise Canceller Tuner(電子式調幅/調頻/多路通道噪聲消除器) |
| KCC1202V | Electronic AM/FM/MPX/Noise Canceller Tuner(電子式AM/FM/多路轉換噪聲消除調諧器) |
| KCF201H | FM Tuner for Car Audio(FM調諧器（用于汽車音響）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| JZ500 | 功能描述:8 ~ 50pF Trimmer Capacitor 110V Top Adjustment Surface Mount 0.177" L x 0.126" W (4.50mm x 3.20mm) 制造商:knowles voltronics 系列:JZ 包裝:剪切帶（CT） 零件狀態:有效 電容范圍:8 ~ 50pF 調節類型:頂部調節 電壓 - 額定:110V 大小/尺寸:0.177" 長 x 0.126" 寬（4.50mm x 3.20mm） 高度 - 安裝（最大值）:0.057"（1.45mm） 安裝類型:表面貼裝 特性:通用 標準包裝:1 |
| JZ58F0046L0Y1G | 制造商:Micron Technology Inc 功能描述:512LCR/256DD 12POP 1.8 X16 HF 128 BALL - Tape and Reel |
| JZ58F0046L0Y1GH0 | 制造商:Micron Technology Inc 功能描述:WIRELESS - Trays |
| JZ58F0046L0Y1GH1 | 制造商:Micron Technology Inc 功能描述:WIRELESS - Tape and Reel |
| JZ58F0046L0Y1GHB | 制造商:Micron Technology Inc 功能描述:WIRELESS - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。