參數資料
型號： JZ48F4L0QTZ
廠商： Intel Corp.
英文描述： StrataFlash Wireless Memory
中文描述： 無線的StrataFlash存儲器
文件頁數： 52/106頁
文件大?。?/td> 1272K
代理商： JZ48F4L0QTZ
Intel StrataFlash Wireless Memory (L18)
April 2005
52
Intel StrataFlash Wireless Memory (L18)
Order Number: 251902, Revision: 009
Datasheet
10.3.1
Read Mode
The Read Mode (RM) bit selects synchronous burst-mode or asynchronous page-mode operation
for the device. When the RM bit is set, asynchronous page mode is selected (default). When RM is
cleared, synchronous burst mode is selected.
10.3.2
Latency Count
The Latency Count bits, LC[2:0], tell the device how many clock cycles must elapse from the
rising edge of ADV# (or from the first valid clock edge after ADV# is asserted) until the first data
word is to be driven onto DQ[15:0]. The input clock frequency is used to determine this value.
Figure 24
shows the data output latency for the different settings of LC[2:0].
Synchronous burst with a Latency Count setting of Code 4 will result in zero WAIT state; however,
a Latency Count setting of Code 5 will cause 1 WAIT state (Code 6 will cause 2 WAIT states, and
Code 7 will cause 3 WAIT states) after every four words, regardless of whether a 16-word
boundary is crossed. If RCR[9] (Data Hold) bit is set (data hold of two clocks) this WAIT condition
will not occur because enough clocks elapse during each burst cycle to eliminate subsequent WAIT
states.
Refer to
Table 11
and
Table 12
for Latency Code Settings.
15
Read Mode (RM)
0 = Synchronous burst-mode read
1 = Asynchronous page-mode read (default)
14
Reserved (R)
Reserved bits should be cleared (0)
13:11
Latency Count (LC[2:0])
010 =Code 2
011 =Code 3
100 =Code 4
101 =Code 5
110 =Code 6
111 =Code 7 (default)
(Other bit settings are reserved)
10
Wait Polarity (WP)
0 =WAIT signal is active low
1 =WAIT signal is active high (default)
9
Data Hold (DH)
0 =Data held for a 1-clock data cycle
1 =Data held for a 2-clock data cycle (default)
8
Wait Delay (WD)
0 =WAIT deasserted with valid data
1 =WAIT deasserted one data cycle before valid data (default)
7
Burst Sequence (BS)
0 =Reserved
1 =Linear (default)
6
Clock Edge (CE)
0 = Falling edge
1 = Rising edge (default)
5:4
Reserved (R)
Reserved bits should be cleared (0)
3
Burst Wrap (BW)
0 =Wrap; Burst accesses wrap within burst length set by BL[2:0]
1 =No Wrap; Burst accesses do not wrap within burst length (default)
2:0
Burst Length (BL[2:0])
001 =4-word burst
010 =8-word burst
011 =16-word burst
111 =Continuous-word burst (default)
(Other bit settings are reserved)
Note:
Latency Code 2, Data Hold for a 2-clock data cycle (DH = 1)
Wait must be deasserted with valid data (WD =
0). WD = 1 is not supported.
Table 10.
Read Configuration Register Description (Sheet 2 of 2)
相關PDF資料
PDF描述
JZC-32F SUBMINIATURE INTERMEDIATE POWER RELAY
KCA370UH AM Tuner For Car Audio(汽車音響AM調諧器)
KCC1102A Electronic AM/FM/MPX/Noise Canceller Tuner(電子式調幅/調頻/多路通道噪聲消除器)
KCC1202V Electronic AM/FM/MPX/Noise Canceller Tuner(電子式AM/FM/多路轉換噪聲消除調諧器)
KCF201H FM Tuner for Car Audio(FM調諧器（用于汽車音響）)
相關代理商/技術參數
參數描述
JZ500 功能描述:8 ~ 50pF Trimmer Capacitor 110V Top Adjustment Surface Mount 0.177" L x 0.126" W (4.50mm x 3.20mm) 制造商:knowles voltronics 系列:JZ 包裝:剪切帶（CT） 零件狀態:有效 電容范圍:8 ~ 50pF 調節類型:頂部調節 電壓 - 額定:110V 大小/尺寸:0.177" 長 x 0.126" 寬（4.50mm x 3.20mm） 高度 - 安裝（最大值）:0.057"（1.45mm） 安裝類型:表面貼裝 特性:通用 標準包裝:1
JZ58F0046L0Y1G 制造商:Micron Technology Inc 功能描述:512LCR/256DD 12POP 1.8 X16 HF 128 BALL - Tape and Reel
JZ58F0046L0Y1GH0 制造商:Micron Technology Inc 功能描述:WIRELESS - Trays
JZ58F0046L0Y1GH1 制造商:Micron Technology Inc 功能描述:WIRELESS - Tape and Reel
JZ58F0046L0Y1GHB 制造商:Micron Technology Inc 功能描述:WIRELESS - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*