- 您現在的位置：買賣IC網 > PDF目錄384577 > JZ48F4L0QTY (Intel Corp.) StrataFlash Wireless Memory PDF資料下載
參數資料
| 型號： | JZ48F4L0QTY |
| 廠商： | Intel Corp. |
| 英文描述： | StrataFlash Wireless Memory |
| 中文描述： | 無線的StrataFlash存儲器 |
| 文件頁數： | 21/106頁 |
| 文件大?。?/td> | 1272K |
| 代理商： | JZ48F4L0QTY |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁
Intel StrataFlash Wireless Memory (L18)
Datasheet
Intel StrataFlash Wireless Memory (L18)
Order Number: 251902, Revision: 009
April 2005
21
4.2.2
128/0 and 256/0 SCSP Package Signal Descriptions
Table 2
describes the active signals used on the 128/0 and 256/0 SCSP.
Table 2.
Device Signal Descriptions for SCSP (Sheet 1 of 2)
Symbol
Type
Description
A[Max:0]
Input
ADDRESS INPUTS:
Inputs for all die addresses during read and write operations.
128-Mbit Die: A[Max] = A22
256-Mbit Die: A[Max] = A23
DQ[15:0]
Input/
Output
DATA INPUTS/OUTPUTS:
Inputs data and commands during write cycles, outputs data during read
cycles. Data signals float when the device or its outputs are deselected. Data is internally latched
during writes.
F1-CE#
F2-CE#
F3-CE#
Input
FLASH CHIP ENABLE:
Low-true: selects the associated flash memory die. When asserted, flash
internal control logic, input buffers, decoders, and sense amplifiers are active. When deasserted, the
associated flash die is deselected, power is reduced to standby levels, data and WAIT outputs are
placed in high-Z state.
F1-CE# selects the flash die.
F2-CE# and F3-CE# are available on stacked combinations with two or three flash dies else they are
RFU. They each can be tied high to VCCQ through a 10K-ohm resistor for future design flexibility.
S-CS1#
S-CS2
Input
SRAM CHIP SELECTS:
When both SRAM chip selects are asserted, SRAM internal control logic,
input buffers, decoders, and sense amplifiers are active. When either/both SRAM chip selects are
deasserted (S-CS1# = V
IH
or S-CS2 = V
IL
), the SRAM is deselected and its power is reduced to
standby levels.
Treat this signal as NC (No Connect) for this device.
P-CS#
Input
PSRAM CHIP SELECT:
Low-true; when asserted, PSRAM internal control logic, input buffers,
decoders, and sense amplifiers are active. When deasserted, the PSRAM is deselected and its power
is reduced to standby levels.
Treat this signal as NC (No Connect) for this device.
F1-OE#
F2-OE#
Input
FLASH OUTPUT ENABLE:
Low-true; enables the flash output buffers. OE#-high disables the flash
output buffers, and places the flash outputs in High-Z.
F1-OE# controls the outputs of the flash die.
F2-OE# is available on stacked combinations with two or three flash dies else it is RFU. It can be
pulled high to VCCQ through a 10K-ohm resistor for future design flexibility.
R-OE#
Input
RAM OUTPUT ENABLE:
Low-true; R-OE#-low enables the selected RAM output buffers. R-OE#-high
disables the RAM output buffers, and places the selected RAM outputs in High-Z.
Treat this signal as NC (No Connect) for this device.
WE#
Input
FLASH WRITE ENABLE:
Low-true; WE# controls writes to the selected flash die. Address and data
are latched on the rising edge of WE#.
R-WE#
Input
RAM WRITE ENABLE:
Low-true; R-WE# controls writes to the selected RAM die.
Treat this signal as NC (No Connect) for this device.
CLK
Input
FLASH CLOCK:
Synchronizes the device with the system’s bus frequency in synchronous-read mode
and increments the internal address generator. During synchronous read operations, addresses are
latched on the rising edge of ADV#, or on the next valid CLK edge with ADV# low, whichever occurs
first.
WAIT
Output
FLASH WAIT:
Indicates data valid in synchronous array or non-array burst reads. Configuration
Register bit 10 (RCR[10], WT) determines its polarity when asserted. With CE# and OE# at V
,
WAIT’s active output is V
OL
or V
OH
when CE# and OE# are asserted. WAIT is high-Z if CE# or OE# is
V
IH
.
In synchronous array or non-array read modes, WAIT indicates invalid data when asserted and
valid data when deasserted.
In asynchronous page mode, and all write modes, WAIT is deasserted.
相關PDF資料 |
PDF描述 |
|---|---|
| JZ48F4L0QTZ | StrataFlash Wireless Memory |
| JZC-32F | SUBMINIATURE INTERMEDIATE POWER RELAY |
| KCA370UH | AM Tuner For Car Audio(汽車音響AM調諧器) |
| KCC1102A | Electronic AM/FM/MPX/Noise Canceller Tuner(電子式調幅/調頻/多路通道噪聲消除器) |
| KCC1202V | Electronic AM/FM/MPX/Noise Canceller Tuner(電子式AM/FM/多路轉換噪聲消除調諧器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| JZ48F4L0QTZ | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:StrataFlash Wireless Memory |
| JZ500 | 功能描述:8 ~ 50pF Trimmer Capacitor 110V Top Adjustment Surface Mount 0.177" L x 0.126" W (4.50mm x 3.20mm) 制造商:knowles voltronics 系列:JZ 包裝:剪切帶（CT） 零件狀態:有效 電容范圍:8 ~ 50pF 調節類型:頂部調節 電壓 - 額定:110V 大小/尺寸:0.177" 長 x 0.126" 寬（4.50mm x 3.20mm） 高度 - 安裝（最大值）:0.057"（1.45mm） 安裝類型:表面貼裝 特性:通用 標準包裝:1 |
| JZ58F0046L0Y1G | 制造商:Micron Technology Inc 功能描述:512LCR/256DD 12POP 1.8 X16 HF 128 BALL - Tape and Reel |
| JZ58F0046L0Y1GH0 | 制造商:Micron Technology Inc 功能描述:WIRELESS - Trays |
| JZ58F0046L0Y1GH1 | 制造商:Micron Technology Inc 功能描述:WIRELESS - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。