- 您現在的位置：買賣IC網 > PDF目錄384577 > JZ48F4L0BBZ (Intel Corp.) StrataFlash Wireless Memory PDF資料下載
參數資料
| 型號： | JZ48F4L0BBZ |
| 廠商： | Intel Corp. |
| 英文描述： | StrataFlash Wireless Memory |
| 中文描述： | 無線的StrataFlash存儲器 |
| 文件頁數： | 42/106頁 |
| 文件大小： | 1272K |
| 代理商： | JZ48F4L0BBZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁
Intel StrataFlash Wireless Memory (L18)
April 2005
42
Intel StrataFlash Wireless Memory (L18)
Order Number: 251902, Revision: 009
Datasheet
8.0
Power and Reset Specifications
8.1
Power Up and Down
Power supply sequencing is not required if VCC, VCCQ, and VPP are connected together; If
VCCQ and/or VPP are not connected to the VCC supply, then V
CC
should attain V
CCMIN
before
applying V
CCQ
and V
PP
. Device inputs should not be driven before supply voltage equals V
CCMIN
.
Power supply transitions should only occur when RST# is low. This protects the device from
accidental programming or erasure during power transitions.
8.2
Reset
Asserting RST# during a system reset is important with automated program/erase devices because
systems typically expect to read from flash memory when coming out of reset. If a CPU reset
occurs without a flash memory reset, proper CPU initialization may not occur. This is because the
flash memory may be providing status information, instead of array data as expected. Connect
RST# to the same active-low reset signal used for CPU initialization.
Also, because the device is disabled when RST# is asserted, it ignores its control inputs during
power-up/down. Invalid bus conditions are masked, providing a level of memory protection.
System designers should guard against spurious writes when V
CC
voltages are above V
LKO
.
Because both WE# and CE# must be asserted for a write operation, deasserting either signal
inhibits writes to the device.
The Command User Interface (CUI) architecture provides additional protection because alteration
of memory contents can only occur after successful completion of a two-step command sequence
(see
Section 9.2, “Device Commands” on page 47
).
Nbr.
P1
Symbol
t
PLPH
Parameter
Min
100
-
-
60
Max
-
25
25
-
Unit
ns
Notes
1,2,3,4
1,3,4,7
1,3,4,7
1,4,5,6
RST# pulse width low
RST# low to device reset during erase
RST# low to device reset during program
V
CC
Power valid to RST# deassertion (high)
P2
t
PLRH
μs
P3
t
VCCPH
Notes:
1.
2.
3.
4.
5.
6.
These specifications are valid for all device versions (packages and speeds).
The device may reset if t
PLPH
is < t
PLPH
min, but this is not guaranteed.
Not applicable if RST# is tied to Vcc.
Sampled, but not 100% tested.
If RST# is tied to the V
CC
supply, device will not be ready until t
VCCPH
after V
CC
≥
V
CC
min.
If RST# is tied to any supply/signal with V
CCQ
voltage levels, the RST# input voltage must not exceed
V
CC
until V
CC
≥
V
CC
(min).
Reset completes within t
PLPH
if RST# is asserted while no erase or program operation is executing.
7.
相關PDF資料 |
PDF描述 |
|---|---|
| JZ48F4L0BTY | StrataFlash Wireless Memory |
| JZ48F4L0BTZ | StrataFlash Wireless Memory |
| JZ48F4L0QBY | StrataFlash Wireless Memory |
| JZ48F4L0QBZ | StrataFlash Wireless Memory |
| JZ48F4L0QTY | StrataFlash Wireless Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| JZ48F4L0BTY | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:StrataFlash Wireless Memory |
| JZ48F4L0BTZ | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:StrataFlash Wireless Memory |
| JZ48F4L0QBY | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:StrataFlash Wireless Memory |
| JZ48F4L0QBZ | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:StrataFlash Wireless Memory |
| JZ48F4L0QTY | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:StrataFlash Wireless Memory |
發布緊急采購，3分鐘左右您將得到回復。