- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1161A1BD (NXP SEMICONDUCTORS) Universal Serial Bus single-chip host and device controller PDF資料下載
參數資料
| 型號： | ISP1161A1BD |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 總線控制器 |
| 英文描述： | Universal Serial Bus single-chip host and device controller |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PQFP64 |
| 封裝： | 10 X 10 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-314-2, LQFP-64 |
| 文件頁數： | 89/127頁 |
| 文件大小： | 2762K |
| 代理商： | ISP1161A1BD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁當前第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁
Philips Semiconductors
ISP1161
Full-speed USB single-chip host and device controller
Product data
Rev. 01 — 3 July 2001
89 of 130
9397 750 08313
Philips Electronics N.V. 2001. All rights reserved.
[1]
[2]
[3]
[4]
[5]
[6]
With N representing the number of bytes, the number of words for 16-bit bus width is: (N + 1) DIV 2.
Validating an OUT endpoint buffer causes unpredictable behavior of ISP1161’s DC.
Clearing an IN endpoint buffer causes unpredictable behavior of ISP1161’s DC.
Reads a copy of the Status Register: executing this command does not clear any status bits or interrupt bits.
When accessing an 8-bit register in 16-bit mode, the upper byte is invalid.
During isochronous transfer in 16-bit mode, because N
≤
1023, the firmware must take care of the upper byte.
14.1 Initialization commands
Initialization commands are used during the enumeration process of the USB
network. These commands are used to configure and enable the embedded
endpoints. They also serve to set the USB assigned address of ISP1161’s DC and to
perform a device reset.
14.1.1
Write/Read Endpoint Configuration
This command is used to access the Endpoint Configuration Register (ECR) of the
target endpoint. It defines the endpoint type (isochronous or bulk/interrupt), direction
(OUT/IN), FIFO size and buffering scheme. It also enables the endpoint FIFO. The
register bit allocation is shown in
Table 75
. A bus reset will disable all endpoints.
The allocation of FIFO memory only takes place after
all
16 endpoints have been
configured in sequence (from endpoint 0 OUT to endpoint 14). Although the control
endpoints have fixed configurations, they must be included in the initialization
sequence and be configured with their default values (see
Table 7
). Automatic FIFO
allocation starts when endpoint 14 has been configured.
Remark:
If any change is made to an endpoint configuration which affects the
allocated memory (size, enable/disable), the FIFO memory contents of
all
endpoints
becomes invalid. Therefore, all valid data must be removed from enabled endpoints
before changing the configuration.
Code (Hex): 20 to 2F —
write (control OUT, control IN, endpoint 1 to 14)
Code (Hex): 30 to 3F —
read (control OUT, control IN, endpoint 1 to 14)
Transaction —
write/read 1 word
Read Chip ID
Read Interrupt Register
Chip ID Register
Interrupt Register
B5
C0
read 1 word
read 2 words
Table 74: Command and register summary
…continued
Name
Destination
Code (Hex)
Transaction
[1]
Table 75: Endpoint Configuration Register: bit allocation
Bit
7
Symbol
FIFOEN
Reset
0
Access
R/W
6
5
4
3
2
1
0
EPDIR
0
R/W
DBLBUF
0
R/W
FFOISO
0
R/W
FFOSZ[3:0]
0
0
0
0
R/W
R/W
R/W
R/W
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1161A1BM | Universal Serial Bus single-chip host and device controller |
| ISP1161BD | Full-speed Universal Serial Bus single-chip host and device controller |
| ISP1161BM | Full-speed Universal Serial Bus single-chip host and device controller |
| ISP1181ABS | INDUCTOR 1.0NH +-.3NH FIXED SMD |
| ISP1181A | Full-speed Universal Serial Bus peripheral controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1161A1BD,118 | 功能描述:USB 接口集成電路 USB1.1 HOST &DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1161A1BD,151 | 功能描述:USB 接口集成電路 USB1.1 HOST &DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1161A1BD,157 | 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1161A1BDFA | 功能描述:IC USB HOST CONTROLLER 64LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
| ISP1161A1BD-S | 功能描述:USB 接口集成電路 USB1.1 HOST &DEVICE CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。